72022 (ASWCSE1) LG Refrigerator - Instructions

Remove back door and then shut water of to the refrigerator. Then remove old valve. Have towel ready for excess water when you remove nut to valve. Install new valve screw to refrig. Turn on water and check for leaks.

Replaced the shelf and drawers. Very easy . Screwed in wheels for draws to slide in and out!

Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock

Followed instructions online

Swapped old one with new one. New one had extra plug not needed.

Remove 2 screws swing light down a little bit and pull it to front unplug wires . The hard part of job was finding new replacement light, Partselect.com was only sight I could find that had new replacement number and had the light . Other sites including LG site would only tell me the part number on old lights was discontinued 2 of sites said try used appliance dealers

Removed back panel and water inlet valve and replaced with a new water inlet valve

Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.

This is a mater of sliding the old tray out. Cleaning the tracks and sliding the new one in. I have had to replace the rollers on the previous drawer. But not this time. which that took approximately 20 minutes
Please note: while the drawer tray is out by cleaning the tracks it gets the little plastic particles off and makes the new one easier to slide. Really should be taken out and cleaned periodically so track and drawer slide easily anyway.

Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.

The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.

I removed the old table, removed the glass, as the new part did not come with glass and removed the front side support. I simply installed both the glass and support on the new part and re-installed the parts.
Couldn't be more simple!!!

The ice bin I ordered did not arrive on time and, when tracking indicated it was delivered, it was not here. I notified customer service and was told that they would cancel that order and I could order again.and make a payment, to include shipping, again and I would be reimbursed. Two days later the first order showed up. I notified customer service that the item had shown up and I installed it therfore requested the second order be deleted. Was told that it was already enroute and they would send me necessary paperwork to return it. upon receipt of the paperwork I followed the instructions bur, when I contacted UPS (as directed) was advised that I would have to pay shipping of about $19. unless Partselect requested and paid for shipping and sent me the shipping label. I received the shipping label but, when I contacted UPS was advised that I would stoll have to pay to have the item picked up at my house and, unless I wanted to pay that cost I should deliver the package to a UPS pick up location........all the way across town through heavy traffic, about 25 miles. I should have kept the second bin along with the first, given it away or thrown it away and the cost would have been re imbursed. Trying to do the right thing, I was responsible for additional cost and aggravation .......Thanks a lot!!!!

Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!