Models > 71462 > Instructions

71462 (ABWESEU) LG Refrigerator - Instructions

All Instructions for the 71462
31 - 45 of 63
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
no heat
I replaced the thermistor, then the gas ignitor which were easy to get to once the drum was out. The gas is still not igniting so not sure where to go from here. Putting the drum belt back on took some muscle. But then I'm 71.
Parts Used:
Gas Igniter
  • Barbara from CUDAHY, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer drum stopped spinning inconsistently and made louder noise when spinning
Viewed YouTube video form parts select to take dryer apart. Very easy to do if you just follow instructions in the video. Nothing too hard to do. Of note the 4 pack roller assembly is a whole unit, so you’ll have to replace the stem unit the old rollers use and not just replace the roller wheels like in the video. That is a different part number from LG. The front 2 are pretty straight forward to unbolt and replace. The back 2, especially one on the left is tighter clearance even with a wrench. If you’re able to pull whole dryer out and take back off, it’s an easier to get the one on the back left.
Also replaced belt just because i had it open, I replaced thermistor previously after getting a Te5 code about a year ago so that helped in taking it apart.
Would recommended doing it all since you’ll have it open.
Once replaced, everything ran again.
Parts Used:
4 PACK ROLLER ASSEMBLY Dryer Drum Belt
  • Ryan from San Francisco, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable), Wrench set
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broke the tub drum
Exchange
Parts Used:
TUB ASSEMBLY,DRUM
  • Sergio from CORNELIUS, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum cracked
Repair was easy, but the part does not come with directions. It is pretty self explanatory if you are used to taking things apart and fixing them. Otherwise there are YouTube videos you can pull up. Dryer runs like it is new again though and it was way cheaper than buying a new dryer.
Parts Used:
TUB ASSEMBLY,DRUM
  • Stephanie from RENO, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not heat
Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.
Parts Used:
Dryer Thermistor
  • Sal from MORENO VALLEY, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer work but wouldn’t shut off when finished cycle, had to shutoff from breaker
With a thin flat screwdriver I was able to pry out the old door switch, I replaced it with the new door switch, pushed back in dryer and so far is working since I installed a month ago.
Parts Used:
Safety Switch Assembly
  • joaquin from MIAMI BEACH, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lamp cover broke
Unscrew the screw, remove old part, place in new part, replace screw and you are done.
Parts Used:
Lamp Cover
  • Lorraine from SEQUIM, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I would turn on the dryer it would run for about 10-20 seconds and then shutoff, and could smell something burning
There’s all sorts of videos on it I watched. It was actually very simple
Parts Used:
Drive Motor
  • Kevin from MASHPEE, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable)
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter burned out
Completely had to dismantle the dryer to get to the igniter.
The screw holding the igniter is a SOB to get at for extraction, and even worse putting back.,
Parts Used:
Gas Igniter
  • EDWARD from KNG OF PRUSSA, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken link vet flap
Removed the old vent trap 3 screws total and replaced the new very quick and easy.
Parts Used:
COVER,FILTER
  • JOSEPH from MANHASSET, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer lint filter lining was falling apart and lint was not being filtered
Ordered a new Dryer Lint Filter Assembly that fit my LG electric dryer.
Parts Used:
Dryer Lint Filter Assembly
  • Gabriella from Lexington, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light bulb in dryer burndt
Removed cover replaced bulb
Parts Used:
Light Bulb
  • Duane from TROY, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer was making a terrible sound.
An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.
Parts Used:
4 PACK ROLLER ASSEMBLY
  • NANCY from ATASCADERO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud rumbling noise
Followed video provided on site
Parts Used:
4 PACK ROLLER ASSEMBLY
  • Michael from RIVERSIDE, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cover fell of due to broken center hinge.
Removed six screws holding filter support in place. Replaced cover (keep track of the small spring on the left stub shaft). Reinstall cover and filter support sections. NOTE: the cover does not come with a new spring. You have e to reuse the old spring.
Parts Used:
COVER,FILTER
  • Michael from Dagsboro, DE
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 71462
31 - 45 of 63