71026 LG Refrigerator - Instructions

Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE

Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape

The ice bin I ordered did not arrive on time and, when tracking indicated it was delivered, it was not here. I notified customer service and was told that they would cancel that order and I could order again.and make a payment, to include shipping, again and I would be reimbursed. Two days later the first order showed up. I notified customer service that the item had shown up and I installed it therfore requested the second order be deleted. Was told that it was already enroute and they would send me necessary paperwork to return it. upon receipt of the paperwork I followed the instructions bur, when I contacted UPS (as directed) was advised that I would have to pay shipping of about $19. unless Partselect requested and paid for shipping and sent me the shipping label. I received the shipping label but, when I contacted UPS was advised that I would stoll have to pay to have the item picked up at my house and, unless I wanted to pay that cost I should deliver the package to a UPS pick up location........all the way across town through heavy traffic, about 25 miles. I should have kept the second bin along with the first, given it away or thrown it away and the cost would have been re imbursed. Trying to do the right thing, I was responsible for additional cost and aggravation .......Thanks a lot!!!!

I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.

Just had to slip the 2 pegs into the existing holes.

Easy job. Just don't get the parts from this place. First part was no good and delivered was past deadline after I paid for expedited shipping. Had to get new part delivered which in three days increased in price and then still waited for ten days WITH expedited shipping. Have not been reimbursed for first part that was no good AND my expedited shipping fee. Shop somewhere else.

Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/

Did not the crisper cover is ok the vegetable tray is ok but the pieces you sent to me no actually fit the crisper in is way off

Go to this site on You Tube to watch the "how to" replace the gasket retainer. The retainer I needed did not come with brackets or the cam you will need. You will need transfer them from the old retainer to the new one. Not hard, just be mindful of position of the items you remove to put them back in place the same way. A metal rod holds the brackets and spring in place with a screw on one end to prevent rod from sliding off retainer. The cam has a screw that holds it in place, use from old retainer. If the old cam is not broken use the one from the old retainer. It is not hard and you will save $$$ that you would pay an appliance repair company.

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

Removed old part very easily and installed the new part without any problems. Used and adjustable wrench and screwdriver

unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.

Just like on YouTube very easy to do

Removed Ice dispenser and installed new one.