71024 ((ABICSE1)) LG Refrigerator - Instructions

remove all trays from refrigerator , remove screw holding rail and install new rail.

Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.

1) Remove three drawers and items sitting on glass shelf.
2) Remove glass shelf
3) Remove entire crisper plastic unit from refrig.
4) Unscrew 6 screws holding uprights with a philips head screwdriver.
5) Remove top frame and replace with new frame.
6) Replace 6 screws and tighten them.
7) Replace entire frame in refrig and replace 3 drawers and glass shelf.
8) Done

Swapped old one with new one. New one had extra plug not needed.

The past I ordered was broken upon delivery. I asked for a replacement and was refunded the charge. Tried to contact you but "due to covid" you aren't taking calls. Net result: I ordered the part from another source, got it, installed easily. Won't use you again.

I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.

Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.

I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.

Once I determined the problem to be the ice maker I got on line and came across "Part Select" website, I simply put in the make & model # and I quickly found the part I needed and placed my order, much to my surprise I received the replacement part the next day. The removal and installation was extremely easy, I simply removed two "Allen" head screws holding the ice maker in place and removed the unit, next I un-plugged the electrical coupling and removed the ground wire. I installed the new part in the same manner the entire process took me less the 15 minutes, and most importantly we had ice in less then 2 hours.

The ice bin I ordered did not arrive on time and, when tracking indicated it was delivered, it was not here. I notified customer service and was told that they would cancel that order and I could order again.and make a payment, to include shipping, again and I would be reimbursed. Two days later the first order showed up. I notified customer service that the item had shown up and I installed it therfore requested the second order be deleted. Was told that it was already enroute and they would send me necessary paperwork to return it. upon receipt of the paperwork I followed the instructions bur, when I contacted UPS (as directed) was advised that I would have to pay shipping of about $19. unless Partselect requested and paid for shipping and sent me the shipping label. I received the shipping label but, when I contacted UPS was advised that I would stoll have to pay to have the item picked up at my house and, unless I wanted to pay that cost I should deliver the package to a UPS pick up location........all the way across town through heavy traffic, about 25 miles. I should have kept the second bin along with the first, given it away or thrown it away and the cost would have been re imbursed. Trying to do the right thing, I was responsible for additional cost and aggravation .......Thanks a lot!!!!

Watched a couple of YouTube videos and then went at it

I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.

Removed back panel and water inlet valve and replaced with a new water inlet valve

Slid new bin into place. It works perfectly now.

Simple replace of door, fits perfectly