All Installation Instructions for LG Refrigerator 70322

The spring that connects the flipper assembly to the left door broke.

Removed the 2 Phillips head screws that attach the flipper assembly to the door. Slide the flipper assembly up to disconnect the top & bottom bracket. Disconnect the quick connect wire assembly behind the center hinge bracket and remove the flipper assembly. Install the new flipper assembly in reverse order.

Parts Used:

Refrigerator Flipper Assembly

Eric from HUDSON, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Left French Door would not close properly

Removed two screws from door and three locking brackets with a small common screw driver. Raised the bracket, slide in the spring, held down the bracket, installed screws and plastic covers. Less than 2 minutes. Easy application no problem with the new spring or ,mullion..

Parts Used:

Refrigerator Spring

Kevin from DADE CITY, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

My ice maker wouldn't release the ice, nothing was frozen and the motor would just bind

I bought the ice assembly motor only, super easy to install, remove the three main screws, lift out assembly, detach the cable. Then remove the screws on the parts, lift the tape, redo everything in reverse and it works flawlessly!

Parts Used:

Refrigerator Ice Maker Kit Assembly

Jodi from WINTER GARDEN, FL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Leaking

Swapped old one with new one. New one had extra plug not needed.

Parts Used:

Water Inlet Valve Assembly

Johnny from MOUNT OLIVE, AL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The refrigerator ice maker needed replacing

The only tool required was a Phillips screwdriver. I disassembled the old icemaker and unplugged the electrical snap in device. I removed the ground wire. Then reversed the steps in replacing the refrigerator ice maker kit assembly. It took slightly over 30 minutes to remove and replace the ice maker.

Parts Used:

Refrigerator Ice Maker Kit Assembly

Larry from GODDARD, KS
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Ice tray cracked

Removed the old one and replaced with new just remember do your do diligence watch YouTube videos makes repair a lot easier

Parts Used:

Refrigerator Ice Maker Kit Assembly

Eugene from ENCINITAS, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The cover had cracked

1. Remove all food from the shelf and take out the crisper drawers.
2. Remove the glass and take out the crisper frame.
3. Take the screws out of the frame that are holding the cover frame in place and remove the old cover frame..
4. Install the new cover and replace screws.
5. Re- install the drawers and glass.

( I'm a 76 yr old female and did it myself with the help of the instructions you provided!). Thanks

Parts Used:

Crisper Drawer Cover Frame - White

Kathryn from Albuquerque, NM
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The original spring in the mullion door broke

I disconnected the refrigerator power, removed the 2 screws holding the mullion door on the left side of the refrigerator French-door (it’s the flap that allows the door to close). Removed the broken spring and installed the replacement spring in its place. Reinstalled the mullion door by putting it in place and installing the previously removed screws.

Parts Used:

Refrigerator Spring

John from ELLWOOD CITY, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Ice tray was not rotating any longer

Took the old one out and put the new one in.

Parts Used:

Refrigerator Ice Maker Kit Assembly

Angela from SAINT JOSEPH, MO
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

rail that holds meat tray broken

remove all trays from refrigerator , remove screw holding rail and install new rail.

Parts Used:

GUIDE ASSEMBLY,RAIL

Steve from GEORGE WEST, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Lower ice maker water feed froze and caused leak. Needed new water valve.

Took pics of original install, removed old valve, water tubes & plugs. Installed new valve, reconnected electronic plugs, water tubes, turned water back on and all has been well since. Thank you for your timely delivery!

Parts Used:

Water Inlet Valve Assembly