66595775891 Kenmore Range - Instructions

Removed the trim by unscrewing 5 screws being careful not to drop glass panel. Had to scrape and paint over rust stains on the glass panel. After paint dried reinstalled with new trim (remodeled part only required 3 screws). Just a little tricky getting screws started while holding up the glass panel.

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

removed drawer below oven, reached under stove and unplugged from outlet, pulled stove out from between cabinets, removed the 8 screws with 5/16 nutdriver from back panel and removed the panel, removed knob from switch , measured length of stem on old switch and compared it to the new switch ( my old switch stems was shorter than the new one so using a pair of pliers I shortened stem per instructions that came with new switch, this was very easy to do ), removed the two screws holding switch to stove and removed the old switch, then I transfered one wire at a time from the old switch to the new one until I had all the wires connected to the new one, used same two screws holding old switch to the stove to mount the new switch to the stove and put knob from old switch onto the new one, installed back panel to stove using the same 8 screws, pushed stove back into place between the cabinets and plugged the stove into the outlet, put drawer back in place below oven door, reset clock and tried out the new switch, so far so good only time well tell if I fixed my problem because it only happens once in awhile

The repair was easy. I had to remove the trim on the other side and the bottom. You slide the new trim on and screw in the bottom two screws.

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

switched out latch asy,rear

I removed the bottom srtip. Installed the new bottom strip, snapped in the side pieces. [The old ones screwed in.] Replaced the original handle. Ready to reinstall door.

Parts arrived extremely quickly. Easy assembly. Would highly recommend partselect.com. Thank you.

Easy repair with Phillips screw driver and needle nose pliers. 1. Turn off Breakers or unplug range, Open oven door and remove the two screws holding the glass top to the oven frame. 2. Slide glass top forward and remove the two electrical connectors at the rear of the glass top, one on each side. 3. Remove the Phillips screw holding the ground wire from the rear top flange of the glass top. 4. Glass top can now be removed and placed glass side down on a padded flat table top. 5. Take a few pictures of the wiring and brackets for reassembly reference. 6. Remove the 4 wires from the defective heating element with needle nose pliers (note locations for reassembly to the new element) 7. Remove the Phillips screw on the rear side of the bracket holding the defective element. Carefully lift off the bracket. 8. Heating element can now be removed. 9. Remove the locating flanges from the defective element and install on the new element in the same locations. Clean glass if necessary and place new element on glass. 10. Carefully locate the flange tangs into the same holes on the bracket, reference photos or other side for locations. Ensure small element bracket was replaced in mounting slot of large bracket and reattach bracket screw. 11. Replace wires to same locations, remove and lightly pinch connectors if they appear loose, then reassemble. 12. Replace glass top on range, reconnect the two electrical connectors and ground wire, slide forward and replace the two mounting screws. 13. Restore power and check new element for function. Extension wires which came with the new element were not needed in this application. Total repair time about 20 min.

I'm still unsure why it broke ,but it was just a matter of removing two screws that hold the handle in place and sliding in the glass...

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

I had some confusion about the correct series number associated with my stove and called Partselect. They confirmed the part I was looking at was correct in less than 5 minutes. I then completed the order online. Even with standard shipping my order was processed immediately and I received the heating element the next day.

Turned off the breaker. Removed the two screws in the front holding the range top down. Loosened the screws holding the element in place while balancing the range top with my shoulder. Removed the wires from the older element one at a time and attached them to the new element. Put the new element in place and screwed back in place. If I had a little help with the range top I think I could have completed it in 5 minutes but I was at home alone and the other stories of doing this repair made it seem easy enough and it was.

My husband had no problem at all with the replacement of the exterior glass.
Slipped it in and attached to hooks and secured with the handle with a screw driver. Be sure to remember the trim doesn't cover the glass it kind of sits behind it. It can be deceiving in a way you may think in sits in front of the glass. Otherwise it was quite easy and the part came quickly in less than 24 hours....this is a great site.

Shut down breaker; remove stove back cover plate (8 screws); remove the control knob; remove knob screws (2); simply remove one wire at a time and replace the coresponding wire to the new control unit; remove the snap ring on the knob bar and snap off to fit the proper length; place the control unit in position and reinstall the 2 screws; reinstall the back panel; position stove and turn throw the stove breaker on; test the burner control.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you