66595182300 Kenmore Range - Instructions

Unplug the stove from outlet so no power going to appliance. Had to use wd on screws to help loosen
Little bit of effort to loosen. Took new element from package. Replaced screws just tight donot over tighten. Plug stove into outlet turned on. Did a automatic clean. Oven clean and baked cake later I am back in business and 63 years. Was quote 240.00 to from a local repair person. When using wd make sure you wipe any drip from before turning on oven.

The video was very helpful.

Unplug stove. Remove the two screws attaching the element to the rear of the oven. Carefully pull out. Disconnect wires. Reconnect wires. Screw back in. Done. The hardest part was moving the stove away from the wall.

removed 3 screws holding the strip and replaced with new strip

It was very easy just two screws. The easiest thing was ordering the part. Your company had a good schematic of my appliance so it made it very easy to get the correct part.
Thank you

We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

Well I had my oven door ducked taped together. I Am a 51 yr old female and I laid on the floor on my back to see if I could get the rest of the molding out without having to take off the entire oven door. I was able yo pop out the rest of the broken molding. I wasn't able to snap in the put it under the front of the oven door hold it together and screw in my new screw on the inside of the oven door. IT WORKED!! If I can do this so can you.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

Watch the video...

Unplugged the range. Opened the oven door and took out the shelves. Took the right screw out, but had trouble getting the left one out do to the age of the range. Unhooked the two wires and took the element out. Put the new one in and hooked up the two wires. Attached the two screws and checked to see that the element laid flat and then tighten screws. Closed the door and plugged the range back in and turned the oven on and it worked perfect.

Followed instructions on urine that you provided. Instructions were great.
Only problem had was the screw was hard to get loose on one due to oven usage from previous people but I got it after a bit and then fairly simple from there. Unplugged and plugged new element in. Works although seems to run a bit hotter than before.

use needle nose pliers to disconnect the element from the power supply. After disconnecting it was easy to repair.

Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great