6657466002 Kenmore Trash Compactor - Instructions

Took under 5 minutes to unscrew old handle and screw on the new one. Identical part to old handle, compactor looks and works like new!

Unscrewed old one. Slide new one in. Screwed in two screws. Done. The handle ended up being black, even though the part was listed as brown.... that is good, because the original part was black.
So glad you had the part. It was pricey, but way less than a new trash compactor!

Replace front legs. Very easy fix.

I flipped this unit over,removed 4 screws to the drive gear.I tore apart found a nut came off the screw rod.Which broke the drive gear.I looked on line found the parts select page.That showed the diagram i needed,to order parts, i needed.The wife and i tackled this task,of repairing this product.The repair was quick and easy.It took less ... Read more than 30 minutes including cleanup.The wife happy,that all that matters.
Jack

Laid compactor over on its side. REMOVED 5 SCREWS holding cover plate to expose gear drive. Found that large drive broke in half. Used screwdriver to start split ring then pliers to pull it off the rest of the way.Take off the washer . Next I needed to losten the 4 nuts holding the drive motor. This allowed me to slip the rest of the driv ... Read more e gear off the drive shaft. It was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Retighten 4 nuts on motor support. Put cover back on with 5 screws 2 in front 3 in back Pushed button it worked.I must mention that this was a Sears compactor but when I went to their online parts they no longer supported it. I found Part select and they suggested I look at a Kitchenaid compactor and after checking out the picture it looked the same,Iordered the part and it was the same. Thanks I guess I'll come to you first now.

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of ... Read more a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....

Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from i ... Read more ts side. Test.

Removed bottom and replaced gears

After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening ... Read more the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!

Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.

So impressed with this Company. Was about to buy new trash compactor, because we couldn't find a handle for an old Frigidair. Found website and on Friday ordered part (only $57...a new compactor would have cost $800). Part arrived ONE DAY LATER and was immediately easily installed by taking out old part which involved unscrewing it and in ... Read more stalling the new one using the existing screws. THANK YOU.

Simply slid handle into door compartment at top, and put in the 2 screws to hold it in place. Very easy to do.

the bearing were the perfect match and instructions helpful. sysem is rolling smoothly

replaced the large gear and put it back together.