66572153300 Kenmore Range - Instructions

The replacement proceeds similarly as for electric range switch replacements described here, only this model is a gas range. The top panel does not lift up because of the feeds to the gas burners. It is possible, using a thin blade, to depress the spring fingers holding the switch in the oven panel, or else to remove it destructively. Be careful not to pull the old switch out too far, or else the wires will pull off the switch connectors and fall inside the oven-side panel cavity. This happened to me. The wires are very short. Another 1/2 inch of wire would have made all the difference. If this happens you have to fish out the loose wire. I gave up on this and took off the back panel (about 8 screws) and then loosened the bottom and sides of the side panel. This allowed me to retrieve the short wire and connect it to the back of the switch while pushing the switch into its mounting hole. Reattach the side panel, the back panel, and slide the stove back into place, and you should be good to go.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great

Using 4 strips of duct tape was useful,in holding the glass to the door.

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

Took the old one out and replaced it with the new one, fits perfect.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

Removed the old burner and instlled the new one. It works great and I am a hero!

Lifted the top disconnected the old valve and replaced with a new one.I believe the valve should have been shipped with two gaskets,. One for the bottom and another for the top. I reused the old one on the top with no problem but would have preferred a new one.

I had to use a dremel to grind the heads off the rusted in screws that hold the burners to the stove top then drill out the screws and use larger sheet metal screws to reassemble. Don't lift the stove top much with the burners attached or you'll bend the gas lines. Two screws inside the top oven hold the top down. Without the rusted screws it would be an easy job.

Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !

I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.