66517159K211 Kenmore Dishwasher - Instructions

Ordered a new Faucet Adapter! Simple

I removed front bottom cover on dishwasher. The drain pump is on right front side. Very easy to remove and to install a new pump.

I had to pull the appliance out from under the cupboard, remove the bottom dish rack, go to the back of the dishwasher and remove the two plastic nuts and the two wires from the heater, then remove the heating element from the inside of the appliance and reverse the order. The dishwasher works fine now.

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.

My dish washer is a under the counter type.On mine there are two screws that screw into the bottom of the counter frame,these are located inside when you open up the door, they will be right on the inside and to the very front of the upper part of the door opening. Remove both screws. Now,be slow and start to pull the unit out from under the counter. Make sure you don't scrastch your floor,you may use a towel.If your dish washer's discharge hose is conected under the sink, go ahead and remove it. If your unit can be unpluged, unplug it. If not throw the breaker.Try to turn your unit on' if it does you still have power still on. Try again.With the unit pulled out so you can see the back, lay on your side and look for to long looking plastic nuts with a wire coming out of them. These nuts are holding your eleament in place.Unscrew both nuts and let them slide down the wires. Pull both of the wires off the eleament.now reach inside and remove the old eleament.Put new eleamen in place, reconect wires and tighten the nuts,caustion not to tighten nuts to tight.Ok hook the hose and eleectric back up,push the unit under the cabanet, and install the two screws.Really hopes this helps.

Remove blown high limit therm.and replace with the new high limit

Googled the problem. Found a really good video about how to fix it. Ordered the part from PartSelect and it came in a couple of days. Son and I fixed it and had it up and going in a little more than an hour. The biggest problem was getting it disconnected from the water, drain and power and then hooking it back up. Old fat guys don't do well lying on the floor with their head under the sink - was why I needed son. Works now just like brand new. I highly recommend PartSelect! Don't know what it would have costs to get a repairman to do it but figured our labor saved us a couple hundred $. Yea!

Replaced the faucet adapter, works fine

Removed unit from counter. Replaced element.

Empty dishwasher remove bottom basket. Disconnect electricity then turn off water. Remove top screws from counter. Slide unit out and gently tip forward. Remove the two wires from connectors on element. Unscrew plastic nuts from element save if reusable. Gently tilt unit back to normal position. Remove old element and install new one and attach to stainless spacers to hold element in place. Tip unit forward. Reinstall plastic nuts. Plug wires back into new element connectors. Tilt back into normal position. Turn water back on check for any leaks and repair if necessary. Turn electricity back on and then slide unit back into original position and replace under counter screws. Test out by running quick cycle wash. It should function normally. During drying cycle open door to be sure it is hot inside. If hot then it is repaired. Let it finish cycle and replace basket. Do not touch hot element as it will burn you.

I bought the portable dishwasher on Craigslist, and it didn't have the connector that goes on the kitchen faucet. Ordered it here, got it in a few days, and didn't need any tools - just had to screw it on. Good as gold!

After finding out how to replace it (on YouTube)the repair went smoother than anticipated. the difficulty was disconnecting/connecting the electrical(BX to electric hook-up to dishwasher) due to the proximity of where it was located(~1" from the floor). Other than that, the unit now works as good as the 1st day when it was bought(~6yrs ago)

Using a Torx screwdriver, I removed the fasteners holding the control panel/latch section of the door on the dishwasher. I tested the high limit thermostat with a multimeter. Just two terminals, one being power in, the other power out. The part had what I have heard call a "high resistance open". In other words, the power was not getting from "A" to "B". Power in - not out. After cutting power to the unit, I removed the part (just pull it out of the retaining clip and pull the terminals from the part). After receiving the part...by the way, really fast delivery...I reconnected the part (it doesn't matter which wire goes where), pushed the part back into the retaining clip, replaced and fastened the control panel, then restored power to the unit. Runs like new.

Shut off water,power. disconnect water line,electric,drain.Pulled dishwasher out,laid dishwasher on it's back.Unplugged electric on pump,twisted pump out.Installed new pump and reinstalled dishwasher.

it was just a matter of snapping the new assembly in place.