66517152K217 Kenmore Dishwasher - Instructions

replaced the faucet adapter I did not save when I change out the kitchen sink faucet set

twist filler hose assembly to the side and slide hose in. place clamps on hose and attach to water supply and valve.

I removed old hose and replaced it with a new one and reinstalled the dishwasher.

Installed the rubber grommet and the door was fixed.Wish the product was made to lasts,second time in three years the part had to be replaced.

Ordered a new Faucet Adapter! Simple

I had to pull the appliance out from under the cupboard, remove the bottom dish rack, go to the back of the dishwasher and remove the two plastic nuts and the two wires from the heater, then remove the heating element from the inside of the appliance and reverse the order. The dishwasher works fine now.

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.

My dish washer is a under the counter type.On mine there are two screws that screw into the bottom of the counter frame,these are located inside when you open up the door, they will be right on the inside and to the very front of the upper part of the door opening. Remove both screws. Now,be slow and start to pull the unit out from under the counter. Make sure you don't scrastch your floor,you may use a towel.If your dish washer's discharge hose is conected under the sink, go ahead and remove it. If your unit can be unpluged, unplug it. If not throw the breaker.Try to turn your unit on' if it does you still have power still on. Try again.With the unit pulled out so you can see the back, lay on your side and look for to long looking plastic nuts with a wire coming out of them. These nuts are holding your eleament in place.Unscrew both nuts and let them slide down the wires. Pull both of the wires off the eleament.now reach inside and remove the old eleament.Put new eleamen in place, reconect wires and tighten the nuts,caustion not to tighten nuts to tight.Ok hook the hose and eleectric back up,push the unit under the cabanet, and install the two screws.Really hopes this helps.

Remove blown high limit therm.and replace with the new high limit

Googled the problem. Found a really good video about how to fix it. Ordered the part from PartSelect and it came in a couple of days. Son and I fixed it and had it up and going in a little more than an hour. The biggest problem was getting it disconnected from the water, drain and power and then hooking it back up. Old fat guys don't do well lying on the floor with their head under the sink - was why I needed son. Works now just like brand new. I highly recommend PartSelect! Don't know what it would have costs to get a repairman to do it but figured our labor saved us a couple hundred $. Yea!

I knew I needed a faucet adapter, but thought I could just go to my local home depot and get the part...not so much. After 3 trips and not getting the part I truly needed I ordered the part from partselect. I received it literally the day after I ordered it, screwed in place with no tools, attached the coupler/hoses to the faucet and washed dishes. I wish I would have ordered the part from partselect before even bother with home depot. I would have saved myself a lot of trouble! Extremely happy! Thank you!

Disconnected the power. Removed the dishwasher mount screws from under the counter. Slid the Dishwasher out. Removed the two wires. Loosened and removed the two heater support nuts. Removed the heater element from inside the dishwasher. Placed the new heater element inside. Tightened the nuts. Attached the wires. Pushed the dishwasher back in place. Replaced the under-counter support screws. Reset the diagnostics message on the dishwasher front panel (This may not be necessary for some) - (Press HI TEMP > AIR DRY > HI TEMP > AIR DRY). All works great. Thank you PartSelect.com for fast shipping and great pricing.

As directed online

I read information on this website about the function of the high limit thermostat. I found that it was the problem by disconnecting the two wires on the thermostat and straight wiring to bypass it. This allowed the machine to work properly so I ordered the high limit thermostat. To replace the part I used a screwdriver to remove the instrument panel and replaced the high limit thermostat by disconnecting the two wires from the old thermostat and connecting the wires to the new thermostat. I then replaced the instrument panel. My machine is working properly again..

We had to pull the dishwasher out the get the heating element brackets loose underneath. We had to put the new heating element in and then we had to figure out which code to program in to make it reset. the last one listed on the installation instructions was the one that worked. I think it was heated dry, normal, heated dry. It would be very helpful if the reset instructions were put in the manual by whirlpool. I am very pleased with my part that I ordered from PartSelect. It came within 2 days of placing the order.