66515973991 Kenmore Dishwasher - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I read the instuctions and snapped it together just following the pictures...reading only when the picture was not enough information for me. My husband thought I pulled it out of the box already put togethr, he did not know I put it together.

Replaced the lower washer arm retaining nut,bearing ring.and seal in about 3 min.The retaining nut had broken off inside - make sure to remove the broken piece-I used needle nose pliers.
The dispenser took about 35 mins. Removed all the screws around the inside of the door and removed panel.Removed screws holding the dispenser and replaced.I took time to give the dishwasher a good cleaning(inside edge).
Now my wife is happy.

Plastic parts on this Kitchenaid dishwasher suffer repeat wear problems from heat and chemical detergents. The retainer nut on the bottom wash arm split horizontally int the thread area, and during operation, the wash arm would rise up and hit the bottom of the lower basket so there was a worn groove in the wing on top of the nut and the dishes weren't getting very clean. Simple replacement, just screw the nut down. Also decided to replace the bearing ring right under the wash arm because it was getting pasted with white crust-like material from hard water and chemical detergent residues. I've dealt with PartSelect twice now, and they are fast and efficient. The online parts breakdowns are easy to follow.

Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.

Removed upper basket and installed the arm. New snap in didn't require phillips screwdriver as old one and new support had split to insert. Replacing upper spray spinner dropped screw down around pump. This caused misery unassembling lower covers to receive Stainless
Steel, so magnet won't help ended up with mirror and hemistat to reach through large screen figures. So make sure to put towel or something in the bottom to catch parts.

unscrewed sprayarm, removed bearing and seal, used PartSelect pic and description schematic to identify part numbers then placed order. Parts arrived in two or three days.

First remove front panel of dishwasher. Held on by 2 screws on bottom of panel. Remove the electrical connections from the dispenser. Remove the six screws on the dispenser and remove dispenser. Reverse steps to install new dispenser. Also remove rinse aid sensor from old dispenser and install in the new dispenser.

Bottom wash arm bearing and seal were severely worn and leaking. Replaced in about one minute with new parts from PartSelect.com, and took the opportunity to clean out the arm -- stringy, fibrous matter was clogging two jets.

Top arm horizontal rubber supply tube was disintegrating and leaked. Replace with Spray Arm Kit -- this took maybe two minutes!

Lastly, two to of the upper right-rear folding rack tine clips were broken -- replacement was difficult as the old, broken clips were very stiff and came off only after much physical persuasion! New clips were installed easitly -- in a "snap". Time ~ 5 minutes.

Best of all, the new parts were delivered to my home within 36 hours of my internet order. I thought the prices were fair, too. Thanks.

I first removed the old part. when i removed the old part i could not get the conector piece off when i when to get a new one they told me i should replace the copper tubing with the more flexable tubing because the copper tubing can kink up and possibly break from the kinking. so i screwed the inlet valve on i put teflon tape on the all the threads of the conector piece screwed it into the new inlet valve with and adjustable wrench then i conected the new tubing, and tightend it down with the wrench i slowly turned the water back on to cheak for leaks. When i saw there were no leaks i turned the water on the rest of the way pushed the dishwasher back in and screwed it into place an i was done.

Removed the rest of the broken retainer plug. Part number was on the top of the plug. Went to Partselect.com looked up the part and ordered it. The right part (important) arrived in a few days. I put the arm back in place, screwed in the new retainer plug and we were back in business. Cost of part about $5.00. Price of not having to share in cleaning the dishes, priceless. Any future problems with any of my appliances, this is the first place I'll look for the needed part.

Pretty simple. Hardest part was working the end clips of the slide to remove top rack. You simply need to squeeze the plastic clip in to slide it out. Once the top rack is out, it was an obvious philips head screw removal and new part replacement.

1-remove upper rack by removing holding clips.

2-remove old assembly from Rack

3-cut old ring guide to accomodate new style (one solid plastic piece) and reglue after accomodating new assembly

4-re-install upper rack

DONE

I was hesitant at buying the Matag made replacement, especially since it was one piece as compared to my 10-year old 3 piece assembly, and my dishwasher is KitchenAid.
Ordered on a Sunday afternoon, had in hand Tuesday same week, one phillips head screwdriver to remove/replace. Everyone smiling!
Did not need to remove upper rack. Simply unscrewed 1 screw, put on new one-piece arm, replaced with same screw.
15 minutes!
Good price/delivery.

Pulled off the old valve using a crescent wrench and screw driver. The replacement part was a 100% exact match. Slapped on the new valve and that baby was water tight. $50 on a new valve is a lot better than $500 for a new washer.

Partselect.com was so easy to use and find the right part. Way more helpful than whirlpool's site, but that's not surprising seeing as they have an "authorized repair technician" page.

Thanks Partselect.com!