66515834000 Kenmore Dishwasher - Instructions

I unscrewed the old water inlet valve from the frame of the dishwasher so that I could manuever my hand around to the backside where the rubber hose was connected. That was the easy part. I then had trouble holding the old valve while trying to unscrew the hot water copper tubing so I screwed it back on the frame. My dishwasher is close to 18 years old and I think that was part of the problem. After soaking in WD40, I finally got the valve out. Then I had to remove the "L" shaped connector to put on the new valve. Everything went back together a lot faster and it's like I have a new dishwasher again. By the way, I am a 53 year old female so that may be why it took me so long.

Removed dishwasher, take to garage, removed lower rack to gain access to top of motor unit. Used star socket wrench to remove upper screws holding top of unit in. Disconnect wires, drain tube and counter weight. pulled motor unit out from inside dishwasher and placed on bench. Proceeded to disassemble motor. Some things were obvious, others not so. replaced old worn out parts with new, used a little lube (Vaseline) in places to assist in getting seals back in place. Instructions were of little help need to pay close attention when tearing unit apart. Reassembled with new seals, installed motor and re-installed dishwasher...NO LEAKS!! Wife and I happy.

Had to pull the dishwashwer out to replace the latch. Did this by unscrewing the 2 screws that hold the Dishwashwer to the under side of the counter. Dishwasher then pulled out easily. Then unscrewed to screws on the latch. The screws were accessed by pulling out the modling/strip around the dishwasher door. Also easy to replace the screws. But sliding it back in was a little harder. Had to shorten the front legs on the dishwashwer to get the back of the dishwasher to go back in. Then screw the front legs back out. Finally re-inserted the screws under the counter that attached the top of the Dishwasher to the counter top.

Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.

No brainer

Removed one screw which connects the upper spray arm mount, the spray arm feed tube, and the upper spray arm. Replaced with new parts ordered from partselect and it works as good as new. Highly endorse this website!

Although the lower rack was a slightly different style than our original, it fit the dishwasher perfectly. We needed to transfer the silverware racks to the new rack and insert one set of removable tines. About 5 minutes and we are very happy with the repair.

The old gasket came out easily, but had calcium deposits in area. I cleaned the area with vinegar and water and waited until it was completely dry. The new gasket went in very easily and looked great. I started the dishwasher and alas, it still leaks, so the problem was apparently not with the gasket, but some other area. But the gasket is nice and new. Any suggestions on next step0 in troubleshooting?

1) Removed the two white clips from the left and righ hand side of the top tray roller rail. this allows the tray to be completely removed and ease access to the washer assembly. The clipe looks like the letter "k", so you will need to close the "k" to almost straight line in order to get it through the hole.

2) Put a sheet or a towel at the bottom of the machine, just incase you drop the two small cross head screws. This prevents the screws from falling to the bottom of the machine.

3) Remove the screws. At this time the washer assembly will/should slip out very easily. very little force is required to pull the assmbely out.

4) Slip on the new washer assembly and put the screws back in place. Tighten screws, Be careful not over tighten the screw as you may crack the plastic flange.

Note: My machine is an older model, so the washer assembly had two screw fixing. The new assembly only had one hole. Although one fixing appeared to be sufficient, I decided to drill a hole on the other side and this worked fine.

5) Replace the top tray, taking some care to ensure rollers are correctly located within the rails. Then replace the clips and job's complete.

screwed it in with my hands

first i picked out the old seal, use a screwdriver to get it started. Then I pushed the new one in after cleaning the seal channel. I fixed it during a commercial while watching my favorite tv show.

Rolled out old, rolled in new.

Simply removed deflectors and gasket, replaced all , took all of 5 mins. workes great now.

Removed new from box and installed rollers as instructed that's all there was , very easy.

Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.