6651570992 Kenmore Dishwasher - Instructions

Unplug Dryer. Remove two screws from front panel of dryer on lower left and right. Dryer front will swing out and up to release the hinges at the top of front panel. Set panel aside to the left and remove wires from switch at inner top left of panel (if necessary). There are 3 thermostats in this dryer. Two are set together at lower left and one is on lower right and sits back a little. This Cycling Thermostat is one of the two (on the lower left) and in my dryer, was the one on the right of these two. Check to make sure the numbers (and wire colors) on the replacement match with the thermostat being replaced, because it could be different from mine (Maytag couldn't tell me the difference). Remove the 3 wires from the thermostat with needle nose pliers and then use a 1/4" deep socket to unscrew the thermostat. Replace in reverse order.

I searched for the 18x5x5 insulation.,ordered it from Part Select. Waited. Company sent wrong part. Called, they gave me a refund, reordered, promised 2 day free shipping. Waited more than a week, paid for 2 day shipping. Received same, wrong part. Still don't have repair done. Looking elsewhere for part.

I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.

Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.

Repair went exactly like the video i watched online. Perfect

Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.

This repair should have been rated "Easy" but because of a) the age of the dishwasher - 25 years and b) the close quarters to replace the spring, it was a bit of a challenge. If I could have pulled the dishwasher out a few inches, replacing the spring would have been a snap. But because of new flooring on top of existing flooring, that wasn't possible. Also the side cabinets were so close that getting a pair of pliers in there to hook the spring onto the door was tough. Ended up cutting out some cabinet facing that wasn't going to effect the look of things in order to get my hands and tools in there to get the hook end of the spring on the door. After I finally got it on and replaced the kickplate, sat back and had a cold one. Whew!

The lower dish rack rolls directly out of the dishwasher without problem - there is no permanent attachment. The new rack comes as a kit, which includes the 4 required dish rack wheels (Part # 6 in the diagram). One part (only) from the original dish rack needs to be removed and re-installed on the new rack - the upper spray arm tower (Part #5 in the diagram). That is easily removed from the original rack with a 1/8 counterclockwise turn, to disengage the 'feet', and installed on the new rack with a 1/8 clockwise turn. The kit is designed to allow for use on multiple models, so there are 'extra' parts left over, after it is used for the DU8500XX-2 dishwasher. These can be discarded.

I replaced the seals per the video instructions.

Nozzle cap rubber housing was split and cracked. It simply unscrews. The replacement was a matter of screwing the new nozzle cap on. My wife was trusted with this installation. Believe me, this indicates how easy it was.

Snapped on the rollers, removed the center part from the old rack that sprays the water and snapped it on the new one. We then bent the back row down so it would acomodate my larger items. My old rack had that feature. You could either have the rack up or down. Now l
ooks beautiful and works perfectly.
Could have used some directions though.

THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.

Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.

Swapped out the old upper dish rack with a new one. A video made the change simple.

watched a video

the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour