66514793N512 Kenmore Dishwasher - Instructions

Hardest part was figuring out how to release and remove upper rack as mine did not match the instructions. After that is was tricky but not overly difficult. The instructions on-line did not make sense, but it all was fairly intuitive process. Take some before pictures, lol. Dishwaswasher works great.

I pulled the rack and removed failed parts, then reassembled. I would note that the videos are helpful as dishwasher racks can be a bit of a puzzle.

Why manufacturers use so much plastic in a heated environment is beyond me. The heat cycle degrades the plastic to failure - poor design!

Removed old tine rows and replaced with the new parts. No tools were needed. Each was replaced one at a time so the old ones could serve as a model for how the new ones were inserted and attached. Not much more complicated than changing a light bulb. Parts appear to be good original equipment quality but quite pricy for these very simple pieces.

Laid on my side amd reach under unit

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Replaced upper rack adjuster on both sides as these adjusters seem brittle due to heated drying over years. Followed YouTube video for repair. Very easy to fix.

Replaced the detergent dispenser on the door. Followed YouTube video with slight modification given moderate difference in model on video and my model. Relatively easy repair that takes a little bit of time.

I took the old wheel assembly off and snapped the new wheel assembly on. It’s that simple. Note the dishwasher rack needs to be empty. Very pleased with this site. Parts came super fast.

In looking at the parts catalog the part I needed didn’t state left or right side piece. I understood that the same part was used on both sides. Knowing the other side may fail also I ordered (2) pieces. Once they arrived I took apart the surrounding element using a screw driver to pop the enclosure apart carefully. I noted where each clip went and re-assembled the enclosure.

Turned off power to the dishwasher. Removed the front panel via the screws on the inner wall of the door. Lifted and pulled out the front panel. Disconnected cable connections to fully remove the front panel. Pressed down on the latches to the left and right side of the door latch. Pulled out the door latch. Put in new door latch until it clicked into place. Reattached cable connections. Put the front panel back on with the screws. Turned back on power to the dishwasher.

Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.

pushed the new retainers in the holes and we are set to go

First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.