Models > 66514353300 > Instructions

66514353300 Kenmore Dishwasher - Instructions

All Instructions for the 66514353300
46 - 60 of 550
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water leak
I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.
Parts Used:
Water Inlet Gasket Inlet Fill Hose
  • J from HARPERSVILLE, AL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
16 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Friction sleeve
Make sure you order 2. One on each side
Parts Used:
Friction Sleeve
  • Dave from PALM BAY, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
14 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rinse aid dispenser was leaking
First I removed the screws holding the outside door panel to the inside door panel. Next (at this was the tricky part) was separating the panels. In our model of dishwasher, there is a layer of Styrofoam between the two panel to reduce noise. Unfortunately the Styrofoam is glued to both panels. Separating it without damage was not possible. So it was done with brute force and the Styrofoam broke in several places.

Replacing the dispenser involved removing six screws, disconnecting the wires and popping the dispenser out. The new one went in easily although there seemed to be a correct amount of tightening to do. It was tricky to get the cover back on because the Styrofoam pieces had to go back together like a puzzle.

Once reassembled, I ran the machine and it leaked at the dispenser. So the cover came back off. This time I played with the adjustment of the dispenser, testing it with the outside cover off, to insure that I had a tight, non-leaking seal. Once done, I put the cover back on and we are back in business.

The new dispensers do not have connections for the "Add Rinse Aid" light. They use a visual indicator on the dispenser itself. I simply taped the wire for the indicator light up and left it inside the door.

One last note, on our unit, the outside door panel is two pieces. I needed only to removed the lower portion for this repair. Unfortunately, I removed both and in the process broke the small plastic end on the door latch requiring me to purchase a new one. Bummer. That was a 10 minute repair though.
Parts Used:
Detergent and Rinse Aid Dispenser
  • Mark from Austin, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
16 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I did not lock the cap good enough and it fell off and melted
I just placed the cap back on, it worked great, fit fine and so glad I found this part. I was thinking of ways to McGyver it, thinking it would be impossible to find a new part. Glad i fount this site and the part.
Parts Used:
Rinse-Aid Dispenser Cap
  • Crystal from Stansbury Park, UT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
14 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Poor seal on old gasket caused water to leak during dishwasher operation.
I simply pulled out the old gasket and pushed the new one in with my fingers. I had to trim about an inch off the length with a utility knife. The seal is nice and tight now and we have no more water leakage.
Parts Used:
Dishwasher Door Gasket with Strike - Black
  • Jennifer from Edina, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
15 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dishtrack wheel came off the track and fell into the dishwasher and melted
I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards
Parts Used:
Wheel Assembly
  • Timothy from huntersville, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
14 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken wheels on upper dw rack
My 2 parts were delivered very quickly. We had been putting off the repair, mainly because any time you hire a capable repair man, the charge to "walk through the door"is very high. I actually thought about buying a new DW for this reason . . . Then I googleD PARTS, And was lucky to find PARTS SELECT. I was most impressed with the graph layout of the parts, which enables the buyer to actually measure the part being replaced to be sure the correct item is being ordered. The instructions were excellent, and this grandmother took care of the repair, easily.
Parts Used:
Upper Rack Wheel with Mount
  • Susan from Hanson, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
14 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher's "clean" light just blinked - wouldn't run. Repairman came and found out problem and suggested I could fix it myself
Since I had watched a repairman diagnose the problem, it was eash to reproduce how to pull the unit out from the wall and find the faulty part to remove it and replace it with the new thermistor. Two wires to disconnect and connect and repair nearly complete. Pushed it back in, screwed it back to the cabinet and installed foot plate and done.
Parts Used:
Dishwasher Thermistor
  • Peter from San Diego, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
15 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stopped running in the middle of wash cycle.
Removed leads from fuse and installed jumper wire (while the power was off, then turned back on) to determine that circuit board was still good. Ordered new fuse and installed using existing wire connections. Did not splice in new connectors that came with fuse. Wires were clean and good and did not want to cut and splice.
Parts Used:
Fuse Kit
  • Gary from Centennial, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
12 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very loud howling noise during operation
Replaced pump and motor. For the price of the products individually, it only made sense to do the whole thing. As someone else mentioned, much easier to remove the dishwasher and turn it on it's side to remove/replace. Disconnect 3 fittings, 3 stop devices and remove. Other than getting about 20 cuts on my hands from all the metal, it wasn't bad at all.
Parts Used:
Circulation Pump and Motor Assembly
  • Patrick from Oak Grove, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench set
14 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor was very loud...........bearings in motor were beyond repair
Replace motor/pump assembly
Parts Used:
Circulation Pump and Motor
  • Mark from Plymouth, WI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
17 of 29 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishes were not cleaned properly, residue
I had removed this part several times before, it had clogged from sediment, so I had practice. That issue was resolved, but I determined the water level during the wash and rinse cycles was low, and the valve appeared to be the culprit. The trick is to remove the valve from the bracket, removing the single screw, and sliding the unit so the tangs on the bracket can be pushed to the rear and then towards the front. When you disconnect the electrical connection, then the valve can be pulled out towards the front for better access and to disconnect, if your supply hose is long enough. That makes swinging the wrench easier. Other wise it is tedious. Make sure to reapply thread tape after reconnecting the supply hose.
Parts Used:
Water Inlet Valve
  • Francis from Baltimore, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Wrench set
12 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clip no longer held spinner in place
Bent the plastic housing down holding the spinner. Slipped the top of clip in slot on top of housing. Attached spinner and bottom of clip by holding top clip and pushing bottom of clip in place. No tools were needed.
Parts Used:
3rd Level Wash Spinner Kit
  • Richard from Sandyston, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
12 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
clean light flashing 7 times would not run
removed screws holding dishwasher to counter top,raised leveling pads,pulled dishwasher out, unplugged wiring,removed hold down nuts from inside dishwasher and installed new heater element, this was all easy the hard part was finding the code to reset the dishwasher there was no paperwork inside the dishwasher although there was an empty plastic holder.The code that worked for my model was with the door open to push the normal wash button then the high temp button three times as fast as you can within four seconds then close the door. It worked and reset the dishwasher which ran a short cycle then shut down as normal and is now working fine.After doing this select the beverage of your choice and relax. Hope this helps someone.
Parts Used:
Dishwasher Heating Element
  • Mark from Winchester, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable), Wrench set
12 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
friction sleeve broke
Unscrewed the top of the dishwasher from the counter top and slid the appliance out part way in order to reach the door spring. I loosened he spring from the bracket then slid the sleeve over the bracket. I reattached the spring to the bracket, slid the dishwasher back in and screwed it to the top just like it was prior to removal. Easy as pie.
Parts Used:
Friction Sleeve
  • Roxy r from GERMANTOWN, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
11 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 66514353300
46 - 60 of 550