66513949K015 Kenmore Dishwasher - Instructions

Kill power to unit. Turn off water supply. Remove front access panel. Remove screw holding valve housing. Remove valve. Disconnect water lines. Replace valve in housing. Reconnect water lines with addition of thread tape. Reinstall valve and housing.

Ordered the door gasket and replaced it. Worked perfect. The trick was to stretch the gasket a little as it went around the top curvatures. It would stick out some and not sit as flat as on the top and sides. This helped it to flatten down better.

pulled the dishwasher out (took the most time-1 hour) and 30 min. to install new door balance kit and springs. Replace both sides while the unit was out.

leveled dishwasher, it was leaning forward, raised front 1/2'", to get level.
no More leaks, WOULD LIKE TO RETURN DOOR SEAL. DID NOT USE SEAL.

THANKS,
PETE GODSHALK

Watch video and followed instructions. Very easy!

1) Pull out dishwasher from under counter. 2) Disconnect spring located at the bottom on each side of dishwasher. 3) Using socket remove pulley wheels from each side at bottom. 4) Install new pulleys on each side. 5) Wind pulley cord around both wheels and attach to one end of the spring on each side. 6) Using pliers extend other spring end to lower frame of dishwasher on each side. 7) Open and close dishwasher door to test. 8) Replacement complete

My wife hired a local repairman when the right side spring cable broke (I was out of town). He took two hours to fix it (and two appointments). The door would then pop open when running. He came back and replaced the latch. Problems persisted. I then ordered new hinges and replaced both in half hour or so. Would recommend doing all of these repairs yourself. None of these repairs are that hard and definitely not worth paying hundreds to do it. Trickiest part is pulling the dishwasher out from the counter without impacting the electrical or water connections. Disconnecting the power is important on all repairs. When you take the screws out of the door to get to the hinges, make sure you have a helper just to hold the door up while removing the last few screws. The left side hinge was really bent (when the right side spring cable broke) - caused the door to be out of square and thus would not effectively close. This was obvious after a 5 minute search on this this and other repair sites. Process that I used: 1. remove screws from both sides holding dishwasher into counter (may have screws into countertop as well). 2. turn off power, 3. pull out dishwasher far enough to see hinges and springs (careful of connections), 4. remove front door screws, 5. take off front panel, 6. remove spring cables (pull cable taut and remove "hook" from hinge)., 7. unscrew two screws holding hinge to door, 8. bend metal fingers around hinge pin to be able to remove hinge., 9. attach hinge in opposite path. 10. repeat on other side (if necessary), 11. reconnect things in opposite order...test door prior to reattaching door panel. Make sure you level the unit with the adjustable feet. Make sure screws in sides of cabinet aren't too tight as it can take the unit out of square pretty easily...

Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy

Pulled out dishwasher to access the sides. Removed onld lines and then unscrewed pulley from frame using socket / nutdriver. Replaced pulleys with new units supplied in the kit and then threaded new lines onto door and springs. Repair complete in less than 5 minutes.

remove the bottom plate with a nut driver and back off on the front leg adjusters. Slide out the dishwasher approx 8-10 inches and remove the broken link. The new one goes on easily. Look at the opposite side if in doubt as to how to attach. Slide the unit back in and tighten the leg adjusters until the unit is secure. reattach the lower front panel which hides the leg adjusters, etc. You're done!

My 2 yr old sat on the dishwasher door while it was open. It snapped both the links on the door causing the dishwasher door to drop every time it was ajar. It was a real danger to the kids or to anyone else unaware of the door given its weight.

I ordered the part from Part Select based model and some of the posts that it was something you can do yourself. Park Select was outstanding as got the part next day and got direction from others (thank you). I did not have either side of the door working so no real gauge but finally understood how it worked once I did a search online for a picture.

Recommendation: if both links (rope) are broken, you will need to hunt down the springs on side/back of machine. The part with small hole connects to the spring, the other to the door. Make a reverse S with the rope through the pully system for tention. I did not initially do the reverse S and the part popped of the door once I closed it. Otherwise, easy thing to do and certainly do not need a repair person.....if you need picture, do a search on dishwasher door pully system

Pulled dishwasher from under the counter and replaced the plastic part with the new part and attached the new cord to the door spring and to the replacement plastic part. replaced the dishwasher under the counter and replaced the kick plate. All Done.

Hardest part of job was sliding dishwasher out. Put in wood floors so limited free space. Had to lower fron foot pegs first, then remove 2 screws from top that held unit steady. Once dishwasher was out a good 16" cords were easy to replace. Did not replace bracket that came with kit. Cords attach to heavy duty spring.

We pulled the unit out and were able to easily see where it broke. We replaced it relatively easy, pushed dishwasher back in; however, somehow the pump seal got broken in the process so now we have to replace the pump. This was totally unrelated to this repair - only can assume it happened when we pushed the unit back into place.

The door balance springs are connected to the door via a nylon cable which snakes through a couple of pulleys. The plastic fastener on the end of one of these cables separated, so the one remaining spring was not able to offset the weight of the door. Easy to fix, just slide the unit out about 15 inches (remove base plate, and undo a couple screws on top) then replace cables. You can buy just the one cable, or for a couple bucks more, both L&R cables and new pulleys. Replaced the pulleys on my unit at the same time (remove one screw and twist out) since the replacement parts were of better quality than my factory parts. Don’t pay a repair guy $250 or more to fix this for you. It’s easy.