66513802N710 Kenmore Dishwasher - Instructions

I saves the old part to see how it was to be installed. It was very easy. I saved the $50 + dollars for a SERVICE CALL.

I followed installation instructions from this site and all went well.

Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.

I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!

Husband is wonderful, tipped dishwasher over on back, disconnected hoses, and drain motor (replaced that a couple years ago), popped out old part, popped in new part. Had me help him keep door open when working from the inside, and flip a plastic holder piece into place on outside. 15 minutes later, I had a dishwasher that worked like new again.

Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.

Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.

Watched YouTube first of course. Pulled off the old gasket, found the center of the new gasket and started installing the gasket from the very top and all the way down the sides. I made sure it was in tightly and smooth. No more leak, should have listened to my wife sooner!

Followed very simple instructions to easily install. The only tool needed was a flathead scredriver to pop off caps to remove old, broken rollers. New rollers simply click into place. Piease aren't cheap, but significantly less than a new dishwasher.

The left side of the console broke during disassembly to get to the latch mechanism. This was to diagnose parts needed to fix a problem that the washer would stop multiple times in the middle of a wash cycle, requiring monitoring a wash to restart the dishwasher when the console light flashed.

Access to the latch mechanism requires removing two torx self tapping (in plastic) screws on the right side, two on the left side and two attaching the sliding latch plate to the console. Since the screws are tapped into thin plastic sleeves, breaking them can be expected, especially as the console ages.

The pictures available on the troubleshooting notes supplied with the parts diagram were very helpful; In the end I learned I didn't have to replace any parts involving the latch mechanism nor the electrical switch. I DID have to disassemble the latch mechanism and clean everything thoroughly of hardened soap "gunk".
The key to success, though was to NOT tighten the screws attaching the plastic latch mechanism to the console very tight as that will cause the sliding part to bind to the console so it can not fall completely on the switch, which caused the original intermittent operation complaint.

I used a flat blade screwdriver to compress one arm of the endcap of the slide rail to free it. I then slid up the locking slide of the old roller assembly freeing it from the upper basket,and put the new part in its place. I then put the roller back in the slide rail and replaced the endcap.

Looked at how the other was installed oh and bought 2 for when the other one fails. Great customer service!!!!

Just snap it in

this job is cake. worst part is removing dishwasher from cabinet. Disconnect water , drain , and power. reove mounting screws in upper door area. Pull unit out and lay it on its face. unplug two wire leads and remove big nuts. Roll unit upright and replace heater. roll unit back over and tighten nuts and plug leads back in. It really takes two minutes to replace heater once the unit is out of cabinet.

Something had been loaded in the dishwasher that had gone thru the basket - it hit the arm sprayer and broke it off.

Replacement sprayer was exactly the same - the partselect website has very specific identification method so you get the proper part. You must have your model number.

I watched a you tube video which was referred by part select. This was helpful.

I did not realize at first that only part of the arm sprayer had broken off. The arm sprayer broke off, but there is a base to the arm sprayer that was still attached to the dishwasher. So I could not, of course , fit the new arm with its base over the existing base because they are the same size. Once I realized this, it was a simple replacement, following the youtube instructions. You do have to press and turn counter clockwise to get the old base off, but once that was done, the new sprayer arm, which arrived attached to the base, easily fit, and press hard to turn it clockwise to reattach it..

It has worked perfectly. It is a hard turn to get the arm sprayer off or on, which is good so it doesn't come loose during washing, but when replacing it, you aren't sure of why it won't turn. It is a hard turn. Watch the you tube video.