66513632K902 Kenmore Dishwasher - Instructions

remove front door outer cover,remove the hex screws holding the dispenser.unplug the wire to the dispenser and remove.replace with the new dispenser, fasten with hex head screws and plug in the wire. make sure you put the vinyl flap back in place. close front door cover and fasten.

First I unplugged the dishwasher.Then I removed 6 Torx screws, popped off cover, cut wires to old fuse, stripped wire, placed wires in new part, tightened screws, reassembled in reverse order, plugged unit back in and tested. WOO HOO!

I saved over $150.00 by doing it myself instead of having a repairman come out! That's 4 free fishing trips!

Primarily, I read the instructions on line and watched the great videos explaining the repair. While the DW was out, I decided to change out the Drain Pump and the Chopper Assembly, even though only the Circulation Pump and Motor was my problem. These three items are the primary mechanical wear components and it made sense to me to replace these items. Perhaps I'll get another 10 years out of the DW. Two notes about the repairs. If you replace the chopper it isn't clear in the video where exactly it fits into the housing as the video mechanic did a great job of blocking the view of this part of the procedure. It took me awhile to figure out the chopper screen didn't go in the narrow trough, but just outside of that trough. Also, to lubricate the gaskets when putting the motor and the drain pump back in, I use a light coating of petroleum jelly. It is a good lubricant to facilitate the insertion of the both pumps. The pumps slid in easily and there were no leaks when I test ran the DW outside of the cabinetry. If you have a modicum of mechanical ability this job is a very simple, straight forward process. Good Luck!

I released the heater element from the clips on the bottom of the waaher tub. I pulled the unit out from the wall and disconnected power. There are two slip on wire terminals on each end of the heater element accessible from the back that need to be removed. One of them was badly rusted from leaking water, which had caused the short, and had to be replaced. These terminals and the crimping tool to install them are available at any home center. I removed and discarded the old plastic nuts since one of them was damaged by arching from the short circuit. Moving around to the front of the dishwasher, I removed the old heater and installed the new one. I had ordered new rubber washers, but the new heater came with them already installed. Since one of the old ones failed and caused the leak, they are a good thing to keep around as spares anyway. I installed the new nuts and tightened them to enough to ensure that the washers made a good seal. I reconnected the wire terminals to the heater, reconnected power and moved the unit back into place. The circuit opening when the heater failed caused a "call for service" error and the controller would not allow the unit to run. You will know you have this by the "CLEAN" LED flashing seven times. Clear the diagnostics by pressing the buttons for "HEATED DRY", "NORMAL", "HEATED DRY", "NORMAL" and after the controller resets, the dishwaher is ready to run. It's worked like new ever since.

Turned off water and disconnected line, then disconnected drain, turned off power and slid dishwasher out and turned turned upside down and removed hold down bolt ( it is a 3/8 head bolt) removed wire from motor and twisted motor assembly approximately 1/4 turn counter clock wise and removed old motor and seal assembly reinstalled new motor with new seal and rewired. Turned washer back upright and removed filter assembly and lower jet arm, removed cover for food disposal and reinstalled disposal blade back on pump drive reinstalled cover and filter assembly and jet arm. Slid unit back in place and anchored down to cabinet and turned water and power back on ran washer through a short cycle to clean any soap build up that was left inside and that was it, it all works just like new.

Turned off power, turned off water supply and diconnected, slid out dishwasher. Removed the spray wand and tilted dishwasher to access the two nuts and disconnet the wires. Removed the two nuts using a socket. Removed the old heating element and replaced with the new one secured with new nuts ( the old ones were fine but since I bought two new ones why not). Pluged the wires back up slid the dishwasher back in hooked up the water reinstalled the spray wand cut on the water and power. Good as new.

We recently installed all new stainless steel appliances, and were considering replacing the dishwasher as well (4 yr. old Kenmore, in good condition, energy star compliant, etc.). We decided to try to find a stainless front panel instead, and Kenmore said for that model they only came in black and white. But after calling Parts Select, they cross indexed our Kenmore model with a Whirlpool model that did come in stainless, and we simply ordered that front panel. The panel fit perfectly, only requiring the removal of 10 screws, and taking the insulation foam from the old panel and installing it in the new, then replacing the screws. Very simple, and economical, fix for our problem. Thanks Parts Select!

Removed the Bi-Metal fuse and ordered a new one and recerved it two days after ordering. Replaced it and it worked.

I had a repair guide for my dishwasher which helped. First I removed the water distribution system inside the dishwasher and then removed the door panel. Next I removed the front bottom access panel. I placed a pan under the pump and hoses to catch water when I removed the outlet hose. Very important here! One must remove the pressure switch from the outlet port or else you can't get the pump clear of the washer tub. Next I removed the drain pump by releasing the catch and turning the pump counter clockwise. Now for one of the hard steps. I had to remove three pins which hold the pump assy to the wash tub. Two of them are out of sight so you have to weave you hand past all the hardware and "feel" for the back two. At this point the pump assy just lifts out. Remove the motor /pump by removing one bolt and turning it counter clockwise and withdrawing. I put the new one in. Don't forget to put the pump screen in as I missed this and had to redo the job. Reverse all the previous steps being careful to keep the motor guard out of the pump seal area. Use lots of silicon seal grease and check for leaks on first power up. It took me a couple of adjustments to get a leak-free seal.

Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.

Disconnected the power and hot water supply.
Removed mounting screws under the counter, and the lower panel screws to expose the leveling screws.
Backed the leveling screws up so that the unit would slide out more easily
Walked the unit out to where I could reach the back side.
Disconnected the two power wires from the heater coil (slide off)
Unscrewed the plastic nuts holding the heater in place and removed the heater coil.
Replaced the heater coil and nuts.
Reversed the process above to install.

This was a fairly easy repair. It took me a little over an hour to complete. First I flipped the circuit breaker for the dishwasher; then I removed the dishwasher from the cabinet and disconnected the supply, and return lines. I removed both racks from dishwasher, the lower washer arm, and the plastic conduit that supplies water to the upper rack. I then turned the unit onto it's side, and pulled the three or so cables that went to the motor, along with the three plastic wedges that held the motor in place. I then pushed the old motor through, into the interior of the dishwasher. This required me to disconnect some additional components to get it to fit through the opening, including the large silver capacitor. I then compared the old motor to the new one, and transferred some of the parts from the old motor to the new one that weren't included with the new one. I then pushed the new motor through the opening. This required a second person, who replaced the plastic wedges, while I pushed on the motor. The cables, supply lines, drain lines, and components that wouldn't fit through the opening were then replaced; the interior of the dishwasher was also reassembled.

My husband pulled out the dishwasher and removed the faulty part and installed the new one. We found info on the parts source website to assist us. Dishwasher works great!!! Someone from the company we purchased it from had replaced it several years ago, and the seal at the bottom had leaked and the motor had siezed because of the water. We also discoved that the water line was severly kinked in 2 places, so we installed a flexable hose. Now my dishwasher is quiet, fills much faster and all this for a fraction of the price of a new appliance. Would recommend this website.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

Make sure you order 2. One on each side