66513479N413 Kenmore Dishwasher - Instructions

Pulled up old spray arm and snapped new on in place. Took less than a minute and no tools. Dishwasher is like new again.

Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.

Open dishwasher door.

Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.

Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.

Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.

Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.

Repeat for right side of door.

Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.

Slide the dishwasher back to the original position under the counter top.

Insert the screws in the top brackets to secure the dishwasher.

I manually attached the track stop to the right track in the disheasher.

I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.

Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.

just replaced broken piece ,,,, very easy ,,, will use you again for parts should the need arise

based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.

Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly

Ordered part; took part out of box when it arrived; took broken part off; put new part on. No tools needed.

Took out racks. And releaseed bar. Released set screws and gentley pulled out unit to expose 5/16th nuts. Removed nuts and cleaned area. Used old gaskets as the new part did not come with the gaskets, Screwed in nuts. Reset bar and set rack on carriers.

1. Moved dishrack and tracks outward then moved just the dish rack only in. 2. Using screw driver, pushed plastic tongue on end cap at track and lifted off the end cap. Repeated procedure on second track on opposite side of dish rack. 3. With end caps removed, pull dish rack out and place on table. 4. Examine each track and remove any pieces of broken wheel mounts. 5. Install new wheel mount on opposite side of dish rack from good wheel mounts. 6. Slide dish rack back in place with all four wheel mounts inserted in the two tracks. 7. Reinstall the end caps on the tracks and the fix is done.

The hardest part was squeezing the tab at the end of the track to pull it up and out so that the old wheel part could be slid out and the new one in. Fortunately, the track is open on the side facing the interior of the dishwasher so you can see what you're doing. Once that was done, it was simple to snap the new part into place, slide the wheel into the track, and replace the tab at the end.

Took off the old bracket with a screwdriver. Replaced with new bracket.

Replaced wheels easily

I followed installation instructions from this site and all went well.