6651338550 Kenmore Trash Compactor - Instructions

The plastic drive gear broke and the unit was locked in the down position. The repair kit contained all of the parts required to fix the problem plus other replacement parts for the gear drive unit. It was very easy (about 20 min.) to replace the gear and other parts. The unit works fine now.

Like others who experienced this problem, I removed compactor from under the counter and laid it on its side. I removed the screws holding the cover plates to the motor and gear/chain box. The larger (4" +/-) plastic drive gear which moves the chain that lowers or raises the compactor ram was broke. Using a socket and ratchet, I turned ... Read more the shaft the gear was attached to in a counterclockwise direction and moved the compacting ram from the bottom position to the top so I could finally open the door, It takes a lot of turns to move the compacting ram to the top so be patient. I then loosened the bolts, in the base, that holds the motor secure and slid the base toward the broken gear putting slack in the chain. I removed the split ring from the shaft and removed the sprocket which originally is part of the gear but was left on the shaft when the gear broke in three places. I elected to not remove the original washer and spacer and put the new gear with sprocket on the shaft, put the chain on the socket and installed the split ring. Slid the motor base back to original position putting slight tension on chain and a proper clearance between the gear and drive shaft (sheet of paper seperation). Reinstalled the covers, tested and was finished.

Unplugged trash compactor and removed from undercounter. Took cover off and removed broken plastic gear. Replaced with new gear and put cover back on

Simply removed the two plastic gears (held on by some sort of clip), put the new gears in place using the spacing instructions that were provided in the kit ....... and it is working!

replaced switch and fixed the problem. Still had one more problem after that though, but got that figured out and fixed that to.

Replacement handle fit perfectly, removed the old one by taking out two screws. I was glad that the part was still available, although a little pricey, because the unit has to be at least 25-30 years old or more.

Removed two screws on the front panel cover and lifted off the cover , removed two small screws on the switch bracket, you need a short nut driver, removed the spade clipped wires from the old switch and replaced them on the new part and thats all there was to it.

Unscrew the bottom, pull out the chain, replace the gear.

I broke the directional switch trying to replace the power nuts..duh huh... ordered a new switch, took off the front panel ( 4 screws) replaced the switch (2 bolts) be careful not to lose the small threaded plate used instead of nuts to secure the switch.. and now it works like new again....partselect is a great resource for the diyer

Compactor ram would go to bottom but not return back up after compaction. Keep running until unplugged. After unplugging flipped unit on its side and remover bottom plate (5) nut screws, exposing gears. Found that the main large gear had fine crack which caused it to spin loosely. Ordered gear assembly and lossened four mount screw on mo ... Read more tor to move it forward and give slack on chain. Hint: Loosen motor mount bolts, DO NOT REMOVE bolts COMPLETELY! Removed broken plastic gear and reassembled with new. Held/ pushed motor back to retention chain and secured four (4) mount bolts Then reassembled bottom plate with screw nuts and it worked perfectly!!

-Removed the forward sliding rail screws...lifted the rails up several inches to access the wheel assembly...bent back the steel tab to access the nuts holding the wheels to the frame...replaced the wheels and bent back the steel tabs to original position. Trash bin now rolls out completely as before

changed out the switch and that fixed the problem

I removed the unit from under the counter. After removing all of the bits of old trash and making sure the chain and gears were not slipping or striped, I knew it was the power nuts on top of the ram. After all of these years they were worn out, almost smooth inside where the threads are. They were easy to locate on your website. I receiv ... Read more ed them in 2 days (faster than expected) and in 10 minutes the unit was back together and working well. Today was the first bag to be taken out after the repair, it is much heavier than the previous ones, a sign that we are now packing much more trash in a single bag!

Someone pulled a Conan on the compactor handle and broke it loose--no one admitted doing it but I have my suspicions. Since the compactor was installed during the first Bush administration, I assumed that the part would be unavailable. I tried to glue it with the latest "super" bond epoxy/space shuttle goop and it would not hold. A frien ... Read more d tried to plastic weld the crack--it worked until Conan showed up again and ripped it loose. I was ready to look for a new compactopr but since it had an insert that matched the custom cabinets--that I knew would not fit on a new unit--I looked on the internet for a part.
The part number was entered, the part was in stock and the order placed on Sunday afternoon. The part arrived on Tuesday and was installed in less than two minutes. It was the high point of the week.

Removed 2 screws holding the old part on. put the new part in place, re-attached 2 screws. Good as new.