66513262K113 Kenmore Dishwasher - Instructions

First I removed everything off of the bottom of the dishwasher. Then I removed the main center piece that everything mounts to. Then I reinstalled the new center piece with the help of some evoo cooking spray (extra virgin olive oil) I sprayed it on the rubber seal to aid in getting that center piece installed without a battle. Then I reinstalled everything else in the reverse order that I removed it. The evoo cooking spray works wonders for more than just cooking !!!

Remove dishwasher from under kitchen counter. Lay down washer on it's back using some towels or other soft material to protect floor. Disconnect plug from pump motor and to get to the hose clamp easily I had to remove diverter motor. Be careful and slide diverter motor out slowly as it needs to engage the disc when putting back together. This took most of the time since I had to orient the disc slot with the diverter motor shaft that has mating tongue that goes into slot. Install pump motor but use liquid dish soap as lubricant to get hose elbow and pump inlet to slide in mating parts. Be sure to lubricate with same on tang that fits into rubber slot. Tighten elbow hose clamp with proper pliers for job. Re-install diverter motor assembly. Inspect for any oops's and install washer back under counter. Hook back up to drain, water and electric power.

watched video took less than 5 min to replace veeeery easy to do

Actually, I found a video on Youtube with excellent instructions once you got past the really simple stuff like disconnecting power and water and drain.
I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.

Followed the easy how-to video from PS. It was as easy as changing a light bulb.

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit

placed sprayer arm in position and twisted it into position, about a 1/4 turn, snaps into place. total of 15 seconds!

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.

The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!

Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

I opened the package took out the replacement part and installed it with no tools. Easy, done in 10 minutes.

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

replaced the whole bracket assembly very easy to do.