66513123K701 Kenmore Dishwasher - Instructions

Removed front instrument cover. Removed latch assembly. Tried to fix it . No luck. Ordered new latch assembly. Came in from partsselect in 3 days. Installed new latch. Replaced cover.

I Removed the upper wash rack by removing locks on each front slide of rack. I laid a towel in the bottom of the washer to keep anything dropped, retrievable. I then removed the top screw closest to the spinner location. I then carefully pulled down on the mounting, which exposed the bad bushing lock. I removed the old bushing lock and replaced with new one. I then replaced the spinner with a push with one hand while holding the bushing in place with the other hand. You will feel a snap as all goes into place. Make sure new spinner spins freely. Now reinstall removed screw. Do not over tighten. Now reinstall lower rack, carefully aligning water feed in rear of washer, and making sure all rollers are back in sliding rack. Reinstall locking tabs onto sliding rack. Now slide out rack, it should not come off slider. Important: now remove the towel in the bottom of the washer. If left in place, you will have a fire during the drying cycle. Close the door and test your washer through a cycle. I felt confident and did a load of dishes. If all went well, spinner should be in place, not in the bottom of the washer.

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher

shut off water take off feed line unhook wire plug in remove one 1/4 in nut and hose clamp and replace thats all then follow steps back wards

Removed the old one, cleaned out the groove, dry fit the gasket, made a small cut to fit length, removed, squeezed the glue into the track and then put gasket in. Had to wait 24 hours for glue to cure.
No leaks.

I followed another story for the same repair. Worked great.

Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.

12 screws remove door outside panel unplug wire remove 6 mounting screw remove old unit put new unit in place put 6 small mounting screws back plug wire in put front door panel in place put 12 door screws in your done now you can start and test run

remover the nut inside of the dishwasher under the float took bottom plate off open the plastic housing installed new the new float switch plug in the wires snip in the new housing put the unit back in the hole put nut back on and put the bottom plate back on easy as pie

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.