66513073K217 Kenmore Dishwasher - Instructions

First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet

Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.

put new hose on, very easy.

I just recently purchased a new house and quickly became frustrated with the dishwasher. The top rack kept falling and interfering with the cycle and loading/unloading was an annoying pain! I investigated purchasisng a new dishwasher even though it wasn't in my budget. I decided to investigate fixing it myself. I was surprised the part was so easy to find and identify on the site. I was elated! It arrived quickly and the dishwasher was fixed in a matter of minutes. The part simply clicked into place! Instead of $500+ for a new appliance, I was saved by a $40 part (with S/H)! I love PartSelect!

It was very simple to remove the old wheel and replace with the new one. Everything snapped out of and into place so no tools were needed and it only took about 3 minutes to complete.

The upper rack for this dishwasher is adjustable. The rack attachment on the upper right side broke and the rack did not stay in position. We ordered the part it arrived promptly and my husband snapped the part into place. Perfect..

I turned off the power to the dishwasher, removed the kick plate, raised the front levelers, disconnected the electric to the appliance, turned off the water supply to the appliance, disconnected the water supply, disconnected the drain system from the garbage disposal, unscrew the appliance from the countertop, then I remove the appliance from underneath the counter. I then tilted the appliance back and then in screwed the plastic retainers that held the heater element in place, removed the old one, replaced it with the new one in reversed the whole process

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.

You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on

The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!

Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.

Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.

I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!