66513044K116 Kenmore Dishwasher - Instructions

Very easy repair !!! I ordered my heating element on a Friday , it was on my porch Saturday. I used the directions that Parts.com sent me . I also read everyones Installation instructions ..... Every step was very easy . I did watch a utube video , so I couldn't screw this repair up......... My wife had a new dishwasher picked out for $ 579.00 , my part was $29 dollars , savings $550 dollar ...... After the repair , I ran the dishwasher and the blinking clean lite took care of itself ... The water has never been this hot and dryers the dishes like it was a new dishwasher ...... My advice , read everyone's Installation instuctions and watch the utube video .....

saw big hole in first (main) hose - got replacement at local hardware thinking it was the only problem - it wasn't - turned on the water and noticed another leak so ordered hose from parts select - fast delivery - installed 2nd hose but still a leak so ordered grommet from parts select - again prompt delivery - installed it and voila no more leak -
also checked for rat entry points, plugged those and put down bait - bait wasn't being taken under dishwasher even tho rat reappeared so put a snap trap in back - no luck so far - teachable moment: might have been cheaper to just get another dishwasher as parts are expensive and its difficult to tell extent of damage - luckily i only needed 3 parts = $150

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

Although the lower rack was a slightly different style than our original, it fit the dishwasher perfectly. We needed to transfer the silverware racks to the new rack and insert one set of removable tines. About 5 minutes and we are very happy with the repair.

Rolled out old, rolled in new.

Watched the video, it went as advertised. Easy repair and the noise is gone.

The cost part plus shipping for each piece which was described as not cleaning properly due to not spraying. Each of these prices is part plus shipping, diverter valve $28.32 diverter motor did not fix the problem diverter motor $125.08 did not fix the problem my next option is the motor assembly which comes out to $311.53. I think they lead you on with the little parts and you work your way up with the big ones expense wise at this point I will simply cut my losses and buy a new dishwasher because I'm almost at what it would cost for a new one and I've had this one for 4 years. When I went to look for what the problem was each one of these said not cleaning properly which I think now is a generic term to just go from the smallest to the largest if I'm going to replace the motor for 300 plus dollars I might as well just buy a new washer

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I pulled the unit away from the cabinet, unplugged the washer and water line(not long enough to reach) removed two nuts from the underside and replaced the heating unit.

Removed new from box and installed rollers as instructed that's all there was , very easy.

First, this replacement kit seems to be of much better quality than the factory original. I was able to remove the old adjuster from the top rack with my hands - did break a little more in the process, but as this was destined for the garbage anyway, I wasn't delicate about it. The new adjuster kit snapped together easily with clear instructions and pictures in a matter of minutes, even with a 1, 3, and 5 year old "helping." Last step requires a screwdriver. I only replaced one side, for now, and it took longer to get the old adjuster off than it did to install new. Done in under ten minutes start to finish and works perfectly!

Dish rack adjuster kit W10712394: I am a fully inexperienced and non-mechanical mom who needed her dishwasher during this holiday season! It took me a little longer and seemed a little harder than the description said it would - but not by much. The dishwasher is now better than it was when we bought it. Tip 1 - The original mechanism had no screws. The replacement kit does. The kit comes with a special screw that you will need in order to use a phillips screwdriver. It would have been helpful to know that before I tried to screw the screws in and stripped the first one because none of my screwdrivers fit. 2- Instructions aren't clear and photos are a little distorted (2D rather than 3D) for a novice. I wish I'd known this request for installation instructions was coming before I finished the project so I could have taken pictures. Tip - Take pictures to submit for installation instructions for others to appreciate. Would be nice to have some kind of perk to motivate people to do the work of clarifying instructions and submitting pictures. 3 - The part that locks the sliding mechanism into place is a little tricky. That step in the instructions needs some attention. I don't know how to clarify it further but other than the problem with the screws, this is the part that consumed time that an experienced dishwasher repair person might have breezed through.

Watched the u tube video. Very clear! He said up front what kind of screwdriver to use and it was necessary to have that kind and size of screwdriver.

The repair was easy. Getting the unit to slide out from under the counter was more time consuming.
After water and power is disconnected, tip the unit over onto one side to gain access to bottom. Look for two white composite plastic posts (insulators) about 2" long each with a single wire inside. Remove the two wire connectors then unscrew the insulators from the old heating element using an adjustable wrench. Inside the box remove the two metal element supports and pull out the old element. Clean and dry the area in and around the openings where the new element will be re-inserted. Carefully place the new element into the holes with the included new rubber washers. Re-install the two metal element supports on the inside of box. On the bottom, re-install the two insulators to the ends of the element, do not to tighten too much to avoid over compressing the rubber washers which could cause premature cracking. Reconnect both wires and check continuity from the door mircro-switch (white-violet) lead to the (white-red) lead on Electronic Controller connector #1 (P6). The circuit thru the element should be good if the Multimeter reads 10-35 ohms. Put the unit securely back under the counter and run a test wash. Works fine now.
I do recommend, if don't know how to use a multimeter or are concerned about accessing the electronic control box; contact a professional.

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.