66513032K115 Kenmore Dishwasher - Instructions

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.

I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.

Very easy repair, take out old seal replace with new insuring the seal in pressed in tightly, while installing. corners were a little tricky.

Removed old part and replaced with new part

Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.

First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.

I removed the lower front panel of the dishwasher to expose wheels and opened door and removed two screws holding washer to cabinet. After raising leveling feet pulled washer out to expose bnotton ow dishwasher. Removed the electrical wires form the heating element and removed screw caps holding the heaqting element in place. Removed the old element and inserted the new, then reversed process to get it back together. It was very easy to do following the instructions I received when I ordered the part.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Following a utube video made it easy. Removed the outer cover of the door to expose latch. Two screws remove the latch, pay attention to how it was positioned and put the new one on and then replace the panel. But first turn off the electricity to the unit at the fuse box.

repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet

Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.

Followed the easy how-to video from PS. It was as easy as changing a light bulb.