Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.
Was this helpful?
Thank you for voting!
Turn on the oven to heat up for cooking, Heard a ark sound, open the oven door and there was a fire on the element. Turn off the oven.
1 personfound this instruction helpful.
Lowell from Aberdeen, MD
Really Easy
Less than 15 mins
Screw drivers
I had to pull the stove out from the wall and discounted the power source from the wall. Than I used the a phillips screwdriver take out the heat element. There was now problem fixing the stove. Lowell Moxley
Was this helpful?
Thank you for voting!
burnt out bake element
1 personfound this instruction helpful.
richard from burnthills, NY
Really Easy
Less than 15 mins
Screw drivers
unscrewed two screws put in new element replaced two screws done, recieved the element within days of order,it was the right part,couldn't have been happier with the service from parts select thank you.
Was this helpful?
Thank you for voting!
Bake Element quit working
1 personfound this instruction helpful.
denise from swartz creek, MI
Really Easy
Less than 15 mins
Screw drivers
Removed the 2 screws that hold the element in place. Pulled the element forward about 3 inches and disconnected the two wires. Plugged the wire clips onto the new element and pushed the element back into place. Put the 2 screws back into place. This was a very easy repair.
Was this helpful?
Thank you for voting!
Defective surface burner
1 personfound this instruction helpful.
Joseph from RICHMOND, KY
Easy
30 - 60 mins
Screw drivers
Removed all surface burners from range, removed range top screws, and suspended range top. Removed plug-in block mounting screw. Cut wires for plug-in block close to original wire-nut junction. Inserted contacts & wires from kit into plug-in block. Slid a provided shrink sleeve onto each wire. Stripped wires on range wires and then connec
... Read moreted them to the plug-in block wires with the provided high-heat wire nuts. Selected one of the two provided plug-in block brackets that matched the original bracket on the range. Used a butane lighter to shrink the shrink sleeves over the wire nut connections. Snapped the appropriate bracket onto the plug-in block. Reassembled everything in reverse order and plugged in new element. Note: my only two issues are that the two high-heat wire nuts provided in the kit were a bit too small for the wire gauge in my Whirlpool range. It took some fiddling on my part by carefully re-stripping the range wires to get the wire nuts twisted on securely. Two more wire nuts of the next size up would have been appreciated. Also, I found that the provided plug-in block mounting screw did not find fit my range. No problem; I simply re-used the original screw. All in all, an easy repair and the element works perfectly.
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this helpful?
Thank you for voting!
Dead Short In Baking Element
1 of 2 peoplefound this instruction helpful.
JIMMY from GRAY, TN
Easy
30 - 60 mins
Nutdriver, Screw drivers
Disconnect power to the oven at circuit breaker. Most important confired power removed by turning on buner,also with electrial meter. Remove hex screw. Pulled purner forward approx 3 inches remove the two wires to burner element . Installed new burner reverse rotation . Returned power to oven,all was well no problems. Not to sure of bur
... Read morener wattage on old and new unit,as two burners are avaiable for this unit. All ok . Thanks to parts select for speedy part needed
Read less
Was this helpful?
Thank you for voting!
Three of four electric coils won't turn on
1 of 2 peoplefound this instruction helpful.
Arsenio from Beaverton, OR
Really Easy
30 - 60 mins
Pliers, Screw drivers
I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as supp
... Read moreort to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.
Read less
Was this helpful?
Thank you for voting!
burned out stove eye, 6"
1 of 2 peoplefound this instruction helpful.
Robert from Birmingham, AL
Easy
15 - 30 mins
remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan
My Orders
