664615 General Electric Dryer - Instructions

Open the dryer door and remove the two screws in the top of the door opening that hold the top of the dryer on, and then remove the dryer top. On the inside of the dryer, there are two screws that hold the front of the dryer on. Remove one screw from each side of the dryer near the top, and the front of the dryer will fall away. The drum slides are visible when you lean the front panel of the dryer out away from the drum. You can replace the drum slides without even removing the front of the dryer completely. Pull out the old drum slides and insert the new slides. Lift the drum slighly from the inside through the dryer door as you tilt the front back into place. Reinsert the screws holding the front of the dryer on and tighten. BE CAREFUL not to drop the screws or you may have to disassemble the dryer to get at the dropped screws. Reinstall the top of the dryer. It is a difficult fit which requres inserting into 3 tabs and sliding the top into place. Check that the top is flush before inserting and tightening the screws in the top of the door opening.

A quick look inside verified that the drum slides were worn through but I also found that the plastic drum bearing that holds the slides was cracked in a couple different places. Ordered a new drum bearing, new slides, and decided to replace the felt seal as well since it looked pretty ratty. Parts arrived quickly after ordering and installation literally took 15-20 minutes. Purrs like a baby now. Steps: Unplug dryer. remove two screws which hold top of dryer to front. Remove two screws which hold front (door) to rest of unit. No need to disconnect wiring to front door, just make sure not to pull the wires out! Install new parts. Put it back together in reverse order.

Tried to replace with home-store bought 6w light. Looked the same, fit into socket, but didn't work. Actually exploded when I turned it on! Be sure to use OEM part like this one. Worked perfectly!

To quiet the noise temporarly I would spray silicone into the dryer drum groove on the front inside panel.Got tired of this and removed the top of the dryer by removing two screws under the front bottom of the dryer top. Remove two screws, one on each side of front panel(screws are on the inside). Lift the front panel straight up and swing to the side. Keep the wires connected to the panel. There is plenty of room to move panel about. Note: I replaced the drum bearing thinking it was a one piece unit with the teflon rub strips. All I had to do is order the teflon rub strips and I would have saved 24 dollars. Reverse the disassembly process to assemble.

Upon receiving the parts, we went to the video repair instructions. We found these videos to be very well done and very helpful. It was great being able to pause the video at specific points until we were able to complete that step of the repair. All of the replacement parts fit correctly and there were no issues.

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

Remove front by removing two screws at top of door opening. Remove front of dryer carefully becsuse of electrical connections for door switch. Drum sliders simply silde in slots at top. (4 are required for total replacement) Door seal simply fits in the groove and locks over end tab. NOTE Do not run dryer any more than absolutelty nessary without lower seal in place.

Searched dryer model on Google, found partselect.com. Searched for Dryer model and a diagram of the dryer with all its parts appeared. Selected the timer knob on the diagram and it took me to the part, ordered it.
All steps took less than 10 minutes, and I had the new knob in my hands the next day and installed in about 3 minutes.
You saved a few dollars, plus not having to miss time from work waiting for a repair man.
Thank you!
Rocio

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

First of all I am NOT a do-it-yourself handyman. I unscrewed the panel where the start knob was diagnosed I needed an electrical switch that went behind the panel and a new start knob. PartSelect was great. just plugged in my model number, found the drawings of the model. I selected and ordered both parts for $40. Shipped normal delivery and they arrived in 5 days. I had the parts replaced, the panel screwed back on and the dryer working in 10 minutes. I highly recommend PartSelect for honesty, speed and helpful drawings that allow you to select the correct part. 110% satisfied.

I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!

Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!

Took apart by removing the top and front panel. Found drum rubbing due to worn glides and felt.

My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell