66213044K112 Dishwasher - Instructions

This kit is not very easy to install. There are no photos to show you how to un-install the broken pieces. Our replacement kit was missing the screws, too, so I'm not happy with the replacement kit. We had to use some zip ties to maybe keep the new parts in place until I can get the correct replacement screws. It would be better if I could have ordered a rack with the side kit already installed. That would be the best for me.

Pulled upper tray out. Removed old adjusters and replaced with new. The pictures in the installation instructions were bad (blurry and hard to distinguish). Had problems with the first side button. Put it in before installing the wheel base on the second side. Went much easier that way. You did need a star tip for the screws.

This repair is simple. However, what you recieve is a box of loose parts and no instructions. The new parts are not remotely the same design as the original. You have to figure out how to remove the old parts (fairly easy by careful prying) but then sort out what the new parts do and how they fit together. It takes patience and some mechanical knowledge. Once you figure it out, it goes quickly. A fairly simple diagram included with the parts would be definite benefit for most people. It seemed like an odd omission. They also include the shortest star driver (about 1 inch long) I have ever seen for the 4 screws but it is useless since you can't really apply enough torque to the screws to properly set them. Be prepared with a standard length star driver.

You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

Only one friction sleeve was broken. So I pulled out the dishwasher to see how the one on the other side went on. It was very easy to replace and I replaced both. Unit works fine now.

Although the b&w photos spooked me a bit. I quickly learned to tear off/break off the old adjuster arms, and then refer to the written directions for installing the new parts. Don't waste your time trying to figure out removal of the original parts, just get them off. So, I did not find the photos helpful, but I figured it out.,with help from the text And of course, once you do one side, the other side is a breeze!

The pictures in the instructions supplied were horrible. I found a video on You Tube that made the install easy

Followed the enclosed direction sheet

The kit number PS10064063 has much improved stainless steel framework. It's apparent the manufacturer recognized the deficiency of the original design. The instructions are adequate but the minimal essential to do the job. The images on the instruction sheet are low quality. Removal of the old parts isn't well instructed. Removal of the clips holding the failed roller mechanism was obvious, but the only way I could see to remove the adjuster was to pry it apart with a flat head screw driver. The Philips-to-hex head adaptor for installing the only two screws for each side that are needed in the new parts is a nice touch, so it isn't necessary to buy a hex screw driver. All in all a very satisfactory conclusion, since the extended warrantee service had declared the model to be unrepairable. The repair kit at reasonable price avoided the problems of having to remove and replace the dishwasher which otherwise is very satisfactory

The kit didn't come with instructions, so I found the following YouTube video

Got all the parts but no installation instructions. Saw the comment about youtube,, reviewed that and everything when together great.

I ordered part PS10064063, metal left and right rack adjusters that should be more durable than the plastic parts that broke. To install, I watched this YouTube video (https://www.youtube.com/watch?v=otUn8eoceBw), pausing and rewinding as needed. Piece of cake! FYI, when the axle broke, the small little plastic prongs stopped the grinder, which caused the dishwasher not to cycle. Fortunately, that was repaired under extended warranty, but the rack wheel was not covered. The repairman said the grinder (in most dishwashers these days) is a very delicate blade. They can't really grind much - even tiny plastic pieces.

The repair was easy: just remove old assembly and replace with new one which was slightly different. The included directions were very poorly printed and practically useless so if you are not somewhat mechanically inclined it would be almost impossible to install just using the instructions provided