6496-LWM-833 Amana Washer - Instructions

We promptly received the part and easily installed it with no tools. We had an excellent experience. We found the old fabric softener dispenser after installing the new one. Now, we have two.

within about 5 minutes I was able to search on the make of the washing machine and then quickly find the broken knob.
this in spite of not knowing the model number for a 25 year old machine. it couldn't have beeb easier than that.

Placed new knob on the post still present on the machine. Very easy. part fit perfectly and works properly with machine.

Found out that these switches go from time to time and are usually the culprit when the washer won't operate. Opened the cabinet facing. Warning: there are plenty of YouTube videos on opening Maytag washers. None helped me with this model. I ended up finding the screws to open near the floor on front. Once it's opened, just replace the faulty switch, reconnect and you're in business. Getting the washer opened was about the hardest part of this repair. Total cost: Less than $30.

I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot

Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.

My husband was the one who installed the parts but which gave him more problems was the hose.

I removed the screws that held the timer/control cover in place. Removed the two screws that held the timer and unplugged the wires. I discovered that the old knob had jammed the timer shaft, so I probably didn't need a new timer. However, I had one ;-) so I installed it along with the new knob.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remove the part but putting the new agitator on was simple.

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.

Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.

I purchsaed a new water valve and it was very easy to install. I hate to do thos kind of repair but it went very smooth. Took maybe a half hour, and now it works like new.

Removed the front panel, could see water leaking from the tub area near the shaft in the center of the machine. Dripping out once the water level reached the hub. Swing the top up, remove the large plastic ring at top of tub. remove the top of the agitor, pulls off easily. Remove the agitator with a firm pull up, not as easy but does come off. Removed the 4 bolt holding the tub. 2 broke off, but not to worry, the new kit has a complete hub. Pulled off the bell seal, pry up. Used an impact gun with 1-1/2" socket to remove the nut. The hub was frozen to the shaft. Tried a puller but ended up breaking the hub. I finally cut it off in pieces and pryed it off (the hardest part of job). Cleaned up the spline with a small file and patience. Installed the new seal kit. Ended up buying the M800 3M sealant on line. I went this far, another $40 for that. Fitted it all back up per instructions. No leaks. All good.

Diagnosing and ensuring that this was the problem took much longer than the actual repair. This was a simple repair, removal of six screws to access the timer assembly, two small bolts hold the assembly in place. Very easy to access and replace.