6432A Norge Washer - Instructions

For this repair the tub must stay centered in the machine. I used a shim between the tub and front panel. Tilt the front of the washing maching aginst a wall and brace if needed. Remove the belt and pully. To remove the stator, I replaced 3 of the 6 bolts with a 2" long bolt of the same thread (replace every other bolt). This is needed because the spring is under 100# pressure. Remove the 3 original blots and than the 3 2" bolts. Remove each of these three a little at a time. Install the new stator and brake rotor. Use the 2" bolts in the stator to compress the spring. Reinstall the the other 3 bolts, pully, and belt.

Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.

We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempted to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??

Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!

Top loader May Tag washer with open bottom. After research I presumed it needed a new belt, or Transmission, which runs 3 pulleys under the open bottom. After tipping the washer back for inspection, saw oil splatter underneath. Removed old belt by turning largest pulley on Transmission while pulling the belt "off" the edge. Belt was aged, Stretched and worn. Belt and all 3 pulleys were oily causing slippage. The main large Drive pulley on the Transmission shaft, has a plastic snap on grease cup at it's center. I snapped it off with screw driver. The cup was partially full of thinned old grease causing the oily mess. There's a C clip inserted in a groove on the end of the drive shaft holding the pulley on. Removed the C clip with screw driver tip and slid off the Drive pulley. The Center of the pulley contains a plastic ratchet assembly that operates the washer tub cycle to rotate and stop and repeat. The ratchet assembly falls right out, and in the end of transmission is a Thrust washer which can be pulled of easily also. I Cleaned all 3 pulleys with De-greaser and finally with Rubbing Alcohol to dry the pulley surfaces. Then cleaned and removed all grease from the plastic ratchet assembly parts and cleaned them. Then I Repacked everything including the Drive shaft with "heavier" Grease that would not break down so easy. Reassembled everything in reverse and installed on the shaft. Snapped the C clip back on to hold pulley back in place and then the Grease cup, which just snaps back in place with a push. Installed new drive belt in the same manner it was removed, only in reverse by turning the pulley, and pushing the belt "on" over the edge of the pulley. Problem fixed and washer works perfect again with Noticeably better operation through all washer cycles.

Hardest part was finding part that needed the needed repair. Searching the web for issues associated with the sound resulted in many links. Once the sound was found, I went to the video to see how to remove the Water Pump so I could examine it to confirm that was the correct piece. It took about 15 minutes to remove the part. Since I had to remove the belt to get it out, I realize that the belt needed replacement as well. So both parts were ordered. Replacing the parts also took about 15 minutes. Relatively easy repair. Be aware that the video on the part select video shows the water pump in a different location than the Maytag washer. To get to the Maytaq water pump, there is a panel in the back that had to be opened to access the water pump.

Actually I got on YouTube and looked up the problem and watch the short video of it and went from there and it showed me how to take everything apart what the problems were and as I did take it apart and found out it was exactly what they said I simply reversed it just ordered the parts and put them in and took my time to make sure that everything was to specs as I've measured the clearance of the break and said all the hardware back in place it was quite simple yet it was just time consuming took me about two and a half hours but it runs quiet spins great just like a brand new one I couldn't be more pleased with it and I saved quite a bit of money doing it myself

First, I unplugged the washer.

then, I used a small prybar to pop open the front top of the waher. It's hinged at the back top edge. I drew a rough sketch of the four color coded connecting wires so I could disconnect the old water inlet valve and replace it the same way with the new one.
( just in case I lost track of which wire went where.)

I cut off the water supply for both the hot and cold water, (you can also cut off the water main,) then diconnected the supply hoses--noting where the hot water was connected, and where the cold water connected. Maytag had cut out a "C" and
a "H" our of the back wall of the washer,
to assist with hose installation.

I unscrewed the two hex nuts holding the old inlet valve to the back wall of the washer. ( from the outside back of the machine.) and pulled the old inlet valve up to the top of the machine. I didn't remove the basket that holds the laundry, so it was a kind of tight workspace.

Once you reconnect the wires to the new water inlet valve, attach the inlet valve to the washer wall, and reconnect the hoses, it's done. It's pretty simple.

unscrewed screw holding old actuater in and replaced it whith the new part.

First i unscrewed the bottom latch to check inside the maching, i then disconected the vertical style pump with pulley from its position and i discoverd a huge crack that was made by a loose pulley. After that i ordered another pulley from this web site easaly installed the pulley and now my maching works like new. The part was less than 50 bucks i saved over 200 bucks by not going out and buying a new machine.

On a scale of 1 to 5 (with 5 being the most difficult), I would rate this a 2 or 3. It is just a matter of knowing how to access the pump. First I unplugged the washer. Then used putty knife to push in clips to lift up top of washer (the clips are located about 1 inch in from each side). Used socket to remove the two screws holding on front panel. Disconnected the two hoses from pump using pliers to squeeze clips (be sure to have cup or bowl handy because water will come out of the hoses). Lifted up washer and removed belt from pump. Used socket wrench to remove pump and replace with new one. Reattached hoses and belt. Reattached front panel and closed the top of the washer. Everything was easy to access.

I checked the belt 1st. It didn't look like it could be the problem, but it needs replacement anyway. Replacing belt is very easy, this 1 is at the bottom of the washer.

1. Unplug washer.
2. Move it away from the wall.
3. Tilt washer back & support the bottom front with lumber.
4. You can see the belt looped around 3 pulleys. Water pump in the back. The motor is in the right front & is spring loaded.
5. Grab the motor pulley & push it back as far as it will go, & remove the belt from it.
6. Do the reverse to install new belt.

There is a Brake Rotor & Lining Assy on this washer. I looked up the part on this web site, sure enough somebody else had this same problem. Part is on order. If this is not the fix, I will revise this posting later.

Popped the top of the washer up and on the right rear of the washer was the valve. Disconnected the hoses and removed the screws, drop the new valve in and replaced the hoses and it was done. Total time was less then 5 minutes. Any one can do it!

took back off washer with nutdriver, pulled wires off by hand, ( was unplugged ). pliars used to remove hose, regular clamp put back on. reinstalled back plugged in, tested water,,,, done

Disconnected the power plug. Turned off the hot & cold hose water supply. Put down old bath towel. Disconneced hoses from machine inlet valve. Opened entire top for access to electrical connections & fill hose. Replaced inlet valve, new wire connectors. Replaced the hot & cold water hoses.

This was my first washing machine repair.

Pop the top of the washer and use the nutdriver to remove the two screws holding the frontpanel on. Use the nutdriver for two more screws holding the plastic motor cover on. Use nutdriver for the two BIG screws holding the motorplate to the washer frame. After this, I literally beat/chiped/sawed the old motor geat off. Once that was done, I put the new one on; had to use a hammer to knock it all the way on (try not to damage the clips). Reassemble everything. Flip washer over and place bet around two smaller gears. Rotate main tub gear to feed belt on. Make sure you use the nutdriver to loosen/tighten the motor positioner screws in the slots if things aren't working here.
The only really hard thing was taking the old motor gear off.