6432A REV D Norge Washer - Instructions

Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump

Reverse the process to install a new pump

Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.

The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.

This was is 1st time we used your server but it won’t be the last!

Kudos to the entire staff and please…keep up the good work.

Sincerely,

Lon Thomas

Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos

Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.

My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.

Unplug power cord; turn off hot and cold water supply; remove water hoses from machine; open top of machine by prying lid open; remove two hex screws holding water inlet valve in place; remove hose from top of old water inlet valve; remove 4 wires; connect bottom set of wires (red and white) to new water inlet valve; reinstall water hose to top of new water inlet valve; install new water inlet valve onto machine using same hex screws; connect remiaining red and white wires; install hot and cold water hoses to machine; turn on water supply valves at wall; reconnect wall plug; turn water type selector to cold, pull out timer and watched the water flow full-force for the first time in 2 years! Have wife give you a hug for saving cost of new washing machine!

I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise!

I followed Gary from Sioux City IA instructions. Very well explained.

changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks

Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and did a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.

Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.

It was easy to replace the water pump

Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.

I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.

diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.

pulled out the washing machine that was the hard part, tilted it back checked too make sure everything spun by hand just to see if that was reason for the belt to snap but everything spun by hand nice and smoothly poped on the drive belt and everything works fine back in business.