64190439 General Electric Dryer - Instructions

- Removed two screws at top left and right of door.
- Removed top dryer panel
- Removed two screws holding front panel in place
- Noticed drum slide was missing because front drum bearing was worn away and slide had fallen off.
- Went ahead and removed drum to replace rear drum bearing (probably not needed; should hav ... Read more e disassembled it first to discover this). Would have been better to pull drum first (loosen idler pulley and release belt, pull drum straight out) instead of attempting to unscrew bearing. Be sure to note how the idler pulley is set.
- vacuumed tons of lint up
- Replaced bearing (needed a second person for this; drum too big to reach around. be sure to pre-thread the bearing)
- Ordered front drum bearing, waiting to repair it now, should be good after this.

Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went aro ... Read more und 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.

drive belt gone, replaced belt and bearing

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Simply pull old knob off..slip new knob on. Less than 2 seconds...done

Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful n ... Read more ot to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!

The gentleman knew what the problem was, sent the right part, and I looked like I was smart.

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Runnin ... Read more g the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together
We are greatful for your service and really happy we didn't have to drive all over to find the part.

Your instructions were execellent
Problem is solve
Thank you

replaced rear drum bearing kit Still makes the same noise

I love the Partsselect.com youtube videos. The man in those videos rocks!!! I did the repair of my rear drum bearing kit exactly as he showed me in his video and it was perfect. I have spread the word on facebook and around work about Partselect.com and friends and coworkers are already checking it out. Hey, everyone loves a good thing. I ... Read more suggest that you do not be afraid, you CAN do it. Tear that baby apart and save yourself some money.

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwi ... Read more se would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!

Started with removal of rear inspection plate on rear of drier,rotated drier drum by hand to look for any visible problems. Found that drive belt with age had lost sections of teeth and every time the bad sections would go past motor they would "thump".
1. Removed belt from tensioner. Done simply by moving tensioner to unload belt. ... Read more r />2. Slipped belt off motor drive and moved belt to front of drum.
3. Opened drier door and removed 4 screws from under the lid or top of drier ,raised lid for access to belt once belt had been slid to front of drum.
4. (steps 4 and 5 are the hardest parts)Worked drive belt between drum and felt insulators keep in mind there are many stamped steel pieces and sharp edges can be present.
5. Removed belt by feeding a small section past felt and drum and worked rest out from frt. top of drier.
6. Installed new belt in reverse order as removal.
This was done without aid of instruction manual and by someone having major back surgery 4 months earlier. No idea how much this saved me but the price of the belt and time and effort involved made it woth my while I'm sure.

Read less