64100149 General Electric Dryer - Instructions

I unscrewed the two screws that are on top of the timer panel either side. and the two screws that are under the timer panel both sides. The whole assembly will come apart and expose the timer. Unscrew the timer (three nutdriver type screws). Unplug the wires (make a map of what color wire goes on what terminal before you unplug them. I h ... Read more ad a wire that melted and burnt on to the terminal. I had to strip and crimp a new terminal onto thr wire. The new terminal is a common one found in hardware store. There is a front panel and the back panel that the Timer knob has to fit between. I forgot the knob and had to take it apart the panel assembly again to get the knob between the front panel and back panel. It is pretty straight forward and easy, once you get the courage to tear the thing apart. Just reassemble it the same way. Oh my dryer is old I used WD 40 on the terminals to get them loose. The replacement part was exactly like my old one. I was worried it would be different but I was pleasantly surprized it was a perfect replacement part.

I changed the two coils for the gas valve and the dryer is now working fine thanks

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtub ... Read more e videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove ... Read more the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

This story first. I went to local hardware where I purchased the dryer over 10 years ago and asked them if they could get me a new knob. I had the model number and serial number. They said sure can, but they are expensive. They told me that the knob was around $20. and that the shipping would be $10-$15. . Both was under $14.00 at this si ... Read more te. Just alined the knob up on the stem and pushed it on. THANKS!!

Removed from lower panel. Just popped it open
with a screw driver.
Unplugged dryer and shut off gas by the gas shut-off valve.
Loacated the gas igniter element and removed it
by pulling up. It is only healed in place by a metel
like a clothes pin.
Using caution slid new unit down and into the pinching device. ... Read more
Plugged in power cord and the gas.
Turned the unit on and it worked !!!
This was worth the try. Better than buying a new
dryer with the economy the way it is now.

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the ... Read more Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in bac ... Read more k wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Took out interlock switch (two leads) and replaced with new one. As simple as that.

i placed the knob on and voila it worked again. the knob was a bit pricey with shipping almost 25.00 but the dryer is 12 years or more old and it is the first repair i had to make so i am very pleased with the dryer and the new knob! the on line photos made it very easy to make sure i was ordering the correct knob with all the views. keep ... Read more up the good work! very satisfied!