- Home
- 63077932011
- Instructions
63077932011 Kenmore Dishwasher - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door on the old rinse additive would not stay closed.
4 of 4 people
found this instruction helpful.
-
Bob from COOKEVILLE, TN
- Easy
- 30 - 60 mins
-
Screw drivers
Ordered the complete soap /rinse additive unit.nturn power off. Take the peripherical screws to remove the front of the door. Slide the door down and off. Unplug wires 2 places. Use a screwdrive to pry the tabs allowing the unit to come out
Important. Add a little Vaseline to the seal on the new part. Press it in until the ta ... Read more bs engage. Reconnect wiring and replace door front. Turn power on Job complete.
Important. Add a little Vaseline to the seal on the new part. Press it in until the ta ... Read more bs engage. Reconnect wiring and replace door front. Turn power on Job complete.
Read less
Was this helpful?
Thank you for voting!
detergent dispenser on Bosch dishwasher was not staying closed
3 of 3 people
found this instruction helpful.
-
RAYMOND from WOODHAVEN, MI
- Really Easy
- 30 - 60 mins
My husband spent minimal time and maybe just screwdriver for repair of replacement part.
Your company was great to work with.
Thank you!
Your company was great to work with.
Thank you!
Was this helpful?
Thank you for voting!
I did not know how to reach the part to be replaced so I took the base off and everything became complicated as I had to put it back, lots of electrical wires, houses aso.
4 of 6 people
found this instruction helpful.
-
Razvan I from Incline Village, NV
- Difficult
- 1- 2 hours
-
Screw drivers
To replace the part per se was simple. To put everything back in place was more difficult as I took the base of the dishwasher off and a lor of other parts in order to reach for the drain pump. The irony was, after I took appart the base I fount a clip on the internet showing how to do that job and that was a very simple thing, couple of
... Read more
screws to take off the toe plate and the interior liner of the door, to create good access to the drain pump. Really a job of 10 minutes at the max.
Read less
Was this helpful?
Thank you for voting!
Rinse aid dispenser lid would not stay closed
3 of 3 people
found this instruction helpful.
-
Sue E from CARMEL, IN
- Very Easy
- Less than 15 mins
-
Nutdriver
Use a screwdriver flat blade to pry up one edge of closed lid. Put one side of lid into hinge and snapped other side into place. Very easy.
Was this helpful?
Thank you for voting!
Lid for the streak treatment wouldn't stay shut.
3 of 3 people
found this instruction helpful.
-
Gary from NEW PARIS, IN
- Really Easy
- Less than 15 mins
Use screwdriver to gently wedge the side of the dispenser body apart enough to pop out the old kid, then insert the new kid in it's place.
Was this helpful?
Thank you for voting!
Broken wheel on upper rack on both sides
3 of 4 people
found this instruction helpful.
-
Joseph from COLLINGSWOOD, NJ
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
The part was perfect. The repair video was very helpful, except it did not include the disassembly of the old part. I figured that out, and all went smoothly until the final step. The screw included required not a slot-head screwdriver which everyone has, not a Phillips head screwdriver which everyone has, but a screw requiring a speciali
... Read more
zed driver that no one has. WHY? I substituted a normal screw and hope that does not mean the terrorists have won.
Read less
Was this helpful?
Thank you for voting!
When loaded, the lower rack would fall off the rails
3 of 4 people
found this instruction helpful.
-
CLYDE from TREGO, MT
- Very Easy
- Less than 15 mins
The problem and solution were described on the internet. I ordered a set of 4 wheels for $43+. I received one wheel. When I called Drew told me that the order was correct, but the description on the web page was wrong. He was to sent me a return label, but it has not arrived. Since then I went to the Bosch website, found the set of wheels
... Read more
(Part 10016657) for $42. They have been installed and the problem seems to have been fixed.
Read less
Was this helpful?
Thank you for voting!
Got the wrong part.......NEVER got an answer to my 3 emails to customer service to find the correct part
3 of 4 people
found this instruction helpful.
-
Donna from SUN CITY WEST, AZ
- Really Easy
- 30 - 60 mins
I ordered the wrong part....needed their help to locate the correct part.
Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?!
Horrible customer service
Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?!
Horrible customer service
Was this helpful?
Thank you for voting!
Droning noise coming from the dishwasher
2 of 2 people
found this instruction helpful.
-
Terrance from Lake Stevens, WA
- Easy
- 1- 2 hours
First of all, I quessed at what was causing the droning noise. It seemed that it started when the d.w. was draining. I looked at various sites to try and figure out what was causing the noise but they all wanted money up front before they would discuss the problem. I gambled that it was the drain pump figuring that, oh well at least it's
... Read more
a part I won't have to replace in the future. I got lucky, the noise stopped with the part I bought. The only issues were the wiring harnesss wasn't the same as in the video I used. Overall, your service was very good. The thing I'm disappointed with is the fact that my expensive Bosch d.w. had to be repaired.
Read less
Was this helpful?
Thank you for voting!
Water leakage from the dishwasher; unknown source.
2 of 2 people
found this instruction helpful.
-
Bill from Seattle, WA
- Really Easy
- Less than 15 mins
Followed the video on your site and it was an easy install with no more leakage.
Was this helpful?
Thank you for voting!
Getting to the part at the bottom of the dishwasher was a little pain.
2 of 3 people
found this instruction helpful.
-
Travis from Hermon, NY
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Everything went great installing the new drain pump. Our dishwasher works like it’s brand new again. I would recommend part select to anyone that needs to repair their dishwasher parts or any applications parts.
Was this helpful?
Thank you for voting!
Chronic water leakage
2 of 3 people
found this instruction helpful.
-
Callan from CHICAGO, IL
- Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set
Replaced ‘sump’ housing , seal was leaking on it- replaced inop float on water level warning system switch, and switch itself as well- replaced drain pump motor attached to sump- replaced o-ring seal at water sprayer inlet valve- replaced water inlet plastic assemble on side of dishwasher- replaced drain hose out of sump assembly.
... Read more r />Used YouTube video to understand repair- this is an involved repair in time and complexity- dishwasher eventually gets turned upside down once removed and stripped down, to remove the white plastic water pan , which then allows access to the guts of all the above parts- some critical seals only come with new assemblies, so you are buying that new part to get a new seal and ensure no new leaks from what you took apart.
... Read more r />Used YouTube video to understand repair- this is an involved repair in time and complexity- dishwasher eventually gets turned upside down once removed and stripped down, to remove the white plastic water pan , which then allows access to the guts of all the above parts- some critical seals only come with new assemblies, so you are buying that new part to get a new seal and ensure no new leaks from what you took apart.
Read less
Was this helpful?
Thank you for voting!
Not getting water
1 person
found this instruction helpful.
-
Ranaye from BECKER, MN
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
shut off water, pull dishwasher out, took side insulation off, unhooked what was connected to the float switch and replaced the new with the old. Reconnected everything and put insulation back and wa-la , all done
Was this helpful?
Thank you for voting!
Clogged, old filter- dirty dishes
1 of 2 people
found this instruction helpful.
-
David from PENN VALLEY, PA
- Very Easy
- Less than 15 mins
Removed old filter and replaced with new filter. Easy.
Was this helpful?
Thank you for voting!
Not pumping out
2 of 5 people
found this instruction helpful.
-
Eric from ELVERSON, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver
Remove spray arm. Pullout. Micro filter big screen . Tork bolt cover and small pliers to grab check valve flapper.
Other Parts Used:
Was this helpful?
Thank you for voting!