63077932010 Kenmore Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Rinse aid dispenser lid would not stay closed
Use a screwdriver flat blade to pry up one edge of closed lid. Put one side of lid into hinge and snapped other side into place. Very easy.
Parts Used:
-
Sue E from CARMEL, IN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leakage from the dishwasher; unknown source.
Followed the video on your site and it was an easy install with no more leakage.
Parts Used:
-
Bill from Seattle, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Got the wrong part.......NEVER got an answer to my 3 emails to customer service to find the correct part
I ordered the wrong part....needed their help to locate the correct part.
Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?!
Horrible customer service
Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?!
Horrible customer service
Parts Used:
-
Donna from SUN CITY WEST, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
When loaded, the lower rack would fall off the rails
The problem and solution were described on the internet. I ordered a set of 4 wheels for $43+. I received one wheel. When I called Drew told me that the order was correct, but the description on the web page was wrong. He was to sent me a return label, but it has not arrived. Since then I went to the Bosch website, found the set of wheels (Part 10016657) for $42. They have been installed and the problem seems to have been fixed.
Parts Used:
-
CLYDE from TREGO, MT
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Getting to the part at the bottom of the dishwasher was a little pain.
Everything went great installing the new drain pump. Our dishwasher works like it’s brand new again. I would recommend part select to anyone that needs to repair their dishwasher parts or any applications parts.
Parts Used:
-
Travis from Hermon, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No water into dishwasher
Remove lower panel
TURN OFF POWER AT BREAKER
Remove water line
Remove the screws on bottom left of washer to remove solenoid valve
Pull out solenoid valve carefully there is a wire plugged into it, far enough to remove clamp on the hose
Remove valve far enough to disconnect wire
Order correct valve assembly
Reinstall in reverse order
TURN OFF POWER AT BREAKER
Remove water line
Remove the screws on bottom left of washer to remove solenoid valve
Pull out solenoid valve carefully there is a wire plugged into it, far enough to remove clamp on the hose
Remove valve far enough to disconnect wire
Order correct valve assembly
Reinstall in reverse order
Parts Used:
-
Samuel from PORT ORCHARD, WA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Waste water won’t drain
-
Kenneth from WESTCHESTER, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not getting water
shut off water, pull dishwasher out, took side insulation off, unhooked what was connected to the float switch and replaced the new with the old. Reconnected everything and put insulation back and wa-la , all done
Parts Used:
-
Ranaye from BECKER, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not pumping out
Remove spray arm. Pullout. Micro filter big screen . Tork bolt cover and small pliers to grab check valve flapper.
Parts Used:
-
Eric from ELVERSON, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clogged, old filter- dirty dishes
-
David from PENN VALLEY, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid for the streak treatment wouldn't stay shut.
Use screwdriver to gently wedge the side of the dispenser body apart enough to pop out the old kid, then insert the new kid in it's place.
Parts Used:
-
Gary from NEW PARIS, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace dispenser
The video pretty much showed it all except...if you have a custom panel on the front like ours did. In that case, yiu have to remove the torx screws along the top PLUS to extras in the side of the part that protrudes into the tub of the washer. Those two are key to releasing the front panel and are also held in with fairly flimsy spring steel so be careful. Otherwise, pretty easy to do.
Parts Used:
-
Andrew from Redding, CT
-
Difficulty Level:Difficult
-
Total Repair Time:30 - 60 mins
Was this instruction helpful to you?
Thank you for voting!