59672013012 Kenmore Refrigerator - Instructions

Removed the grill and control cover in the top middle of the main compartment, removed the control, unplugged it and put in the new one. The thing that took the longest was figuring out that this was the part that needed replacing. The fridge is less than two years old and about 6 months ago the control started making these odd noises. Now it's quiet. Ah peace!

First, I removed the old door gasket by pulling it out of the channel it was mounted in, noting the orientation of the gasket. Then, it was a simple matter of lining the new gasket up with the channel and pressing it into the groove. Very easy repair, and the door seals great!

Shut down refrigerator at the breaker. Placed freezer items in a cooler. Removed top shelf. You must release roller covers on each side to remove the shelf ( Two front screws must be removed) Took off freezer door. (4 screws holding the door to the bracket) Disconnected ice maker electronic plug. Totally removed bottom screw holding ice maker. Loosen two top screws and remove ice maker. Reverse process to install.

Removed screws from cover tested for power to motor found power was on to motor but motor did not work. I went to your web site was able to locate part in about 5 minutes . Even with over night shipping the part came to about $50,00, far cheaper tha a service call would have been.

Thanks John Paulsell

I opened the freezer door and peeled out the freezer gasket, inserted the new gasket, and closed the door. I repeated this same process for each of the French doors on the refrigerator. This was very easy to do. The only issue is the replacement gaskets don't seem to have any better stick or magnetic hold than the original gaskets, so I'm not sure the repair will improve the energy efficiency / performance of the appliance.

Unpacked, inspected, found two minor defects in the form of two tiny slivers along the seal edge which I cut with a small scissor, laid the seal down on the kitchen table, applied heat to the deformed areas and reshaped them with my fingers, heated the entire seal lightly, removed the old seal starting at the right hand upper corner using my fingers, installed the warm seal starting at the top corners by pushing it in its slot making sure the outer lip stayed out of the slot and worked my way around. I believe that the heat from the dryer made it pliable and easier to manage.

Removed all of the bottom drawers and shelvs, then removed the end panel that contained the broken Deli cover hinge pin. Replaced with new panel, cleaned all of the existing parts and ten re-assembled.

First I removed the drawers and shelf above the pantry drawer and then removed the pantry drawer. The end cap came off very simply by removing two screws. I removed the slide attachment to the old end cap and attached it two the new end cap. I then installed the new end cap and replaced the drawers and shelf. The lid to the chef pantry popped right in place. Job complete.

Freezer would get cold at bottom and some of the refrigerator. Took of freezer back panel and located freezer fan. Took a meter and saw power was getting to it, but not working. Removed fan and replaced with new on, working like a charm. Cold air was not circulating enough throughout the unit because fan was not working. It was not the thermostat or adapter control.

The end cap is a very easy job to remove. Removed the three screws that hold the end cap in place using a 1/4 drive socket. Removed sliding rail which is affix to end cap to be reused with new end cap. Installed new end cap with the three screws and your done very easy. What made the job possible was the ability to identify the part from the PartsSelect.com web site which has excellent parts identification catalog.

Popped out old gasket and popped in nwe one. This is where things get interersting, the new gasket
Does work as well as the one I replaced. I think the maganet is not strong enough. If anyone has had the same problem please let me know. This model ( Maytag- French door ) has been a lemon.

changed the starter connected to the compressor

Lifted out the glass shelf and then removed two screws to get the right side end cap off. This side has a mechanical slide to adjust the amount of cold air into the Deli area.

You will need to carefully remove the plastic slide linkage from it's guides so that you can turn it sideways and it will then come off the end cap.

If it wasn't for that minor slowdown it would be a five minute job.

Thanks to this web site for QUICKLY getting me the part and providing info on how to do the job.

First and foremost shut off the water supply to the Ice maker. Some recommend unplugging the refrigerator or disabling the circuit breaker to the refrigerator. Then after emptying the freezer remove the freezer door by loosening the four hex head screws and lift the door straight up and set it off to the side.You can then remove the lower basket. Now locate the clamps located at the rear sides of the inner basket and use a small flat blade screwdriver to gently push the tabs toward the outside of the side clamps while pulling up at the same time and releasing the clamp. Now repeat this procedure on the opposite side of the inner basket. The inner basket can then be pulled out being careful to not damage the roller tracts or gear rollers. Three hexhead screws secure the ice maker to the wall. The screw under the ice maker must be removed while the two on top just loosened. The electrical plug is removed by depressing the tabs on the top and bottom of the plug and then pulling outward. Carefully lift the ice maker upward and out from the two upper hex head screws. You can then install the replacement icemaker by reversing the procedure.

Took the new door seal out of the box, layed it out as straight as possible heated it with hair dryer 4 1hour took the old 1 out by hand and replaced it with new one no tools needed 10 min job