59669279990 Amana Refrigerator - Instructions

I removed all food items from inside fridge/freezer doors.I then noticed how gaskets slip behind outter skin of both doors after removing all screws except a few on the top, inorder to keep from having entire door skin fall to the floor.Using back of spoon helps to properly fit gaskets into place without any rips.Using nut driver really helps with saving time and the "hairdryer" suggestion really helps with having gasket seat firmly around entire unit.Just take your time and pay attention to corners,they may need a little streching.

Took back cover off inside of Freezer. Removed fan and motor assemby and replaced with new parts from Partselect. The assemby came already put together, and was easier than I thought it'd be. Assembly comes with fan, motor, and metal housing. All you need is to screw it in, plug in the three wires, and its good to go.

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self

Unplugged the refridgerator and cleared out the freezer section. Removed the panel at the back of the freezer(six 1/4 in screws )with a nutdriver and two screws on the evap.fan cover.

Moved the panel to one side and removed the wiring off the evap.fan assembly.

Then removed and installed the new assembly, re-attached the wiring and replaced the back panel and fan cover.
The assemble was identical to the one being replaced.

Total time about 25 minutes.

Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.

This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same time to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.

Pretty simple really after reading online some other owners' experiences. This is a bottom freezer unit. Remove the ice maker, the tray slides, and the back cover of the freezer box. In my case I had to thaw it out with a hair dryer as the cover was frozen in place. I checked the old 'stat and found it was bad; I temporarily wired the leads together until the new 'stat arrived. It does allow the refrigerator to warm up during a defrost cycle but it beats de-icing it twice.The defrost 'stat is clipped over the refrigerant line in the upper right corner of the box. Resistance was 65k ohms and wouldn't close on low temp (tested by clipping it to an exposed refrigerant line in another upright freezer) but there was no obvious damage. The one lead on the replacement 'stat has the wrong connector so you have to cut off the original lead from the old unit and splice it on the wrong lead on the new one. I used an epoxy sealed heat shrink type butt splice. Reassemble and let it run. One word of warning: be careful tightening any screws as they will strip easily

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Very easy to order from parts select. Took seconds to replace.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

The repair went very well. Once the sockethead cap screws were taken out of the seal and the ripped seal was removed, the door panel separated from the door itself allowing me to see that ice had already been forming within the insulation. I was fortunate to have decided to replace the seal when I did or further damage would have occurred. After thoroughly cleaning the refrigerator and freezer I replaced the seal using a hair dryer as suggested to tighten the seal into place. Everything is working as it should once again.

Refrigerator door was removed and placed on a set of "horses". Fastners were loosened about 3/4 thread length. Old gasket removed. New one installed. It was necessary to use a "hair dryer" to take out shipping kninks.
Used a piece of 1 1/2 inch sheet styrofoam to seal the door
opening during the process so as not requiring emptying the
unit.

The freezer door was a bit more difficult. This one was done in place. The Styrofoam sheet was cut down and fit in this opening as mentioned above. Inner door panel was removed to reveal heavy ice build up inside door. This was allow to melt and removed along with the fiberglass insulation. New fiberglass insulation was installed and the door reassembled.

In general everything went quite smoothly. Fit on both gaskets was really good.

First time refridgerator repair, I was lucky this was not that bad of a job.

Removed food from freezer, took off ice maker by removing three screws, removed back panel by removing six screws. Once the back panel was removed, the fan assembly could be viewed while powered up. It was not spinning and air was not moving above or below the fan. I removed the electrical connections by hand (with the 'fridge powered down) and removed the fan assembly by removing the two screws adhering it to the back of the freezer section. I replaced the fan assembly and had some difficulty because the new unit shipped by partselect had the electrical connections on the opposite side than the original assembly. The wires were barely long enough so I was able to make the connections and subsequently attached everythng in the same manner it was removed and the fridge works great.

I removed the screws holding the side onto the drawer, removed the side, placed the new one on and put the screws back.

Loosen bolts, remove gasket. Replace gaskets then tighten bolts.
The gaskets new were very out of shape when they were delivered this made it very difficult to put them back on. Even after warming them up with the hair dryer.