59661802101 Amana Refrigerator - Instructions

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .

Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.

There was water on floor at front and ice cubes in freezer were wet.
Freezer cooling cycle had become warmer.
Received part. disassembled the temperature control; i.e., pulled off the control knob; removed 3 screws holding unit to top of freezer; pulled two wires from their connectors to the old "control unit"; pushed them onto the connections of the new unit; reassembled the control to the top of the freezer with the three screws and pushed on the control knob.

bybob

Did the troubleshooting with online instructions and a multimeter. Bought the new thermostat. Disassembled the freezer compartment using a nut driver to expose the evaporator, etc. The thermostat was easy to locate in the upper right hand corner. The new thermostat had one wire that didn't have the correct connector on it so I stripped the wire back and used a crimp connector and heat shrink to attach the connector from the failed thermostat. After plugging the new thermostat in I ran the refrigerator for 15 minutes to cool the thermostat and then rotated the defrost timer to the defrost position and tested the new thermostat. Reassembled the freezer compartment.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

First, I shut off the water going to the refrigerator, then removed the ice bin. Then I loosened the two screws on the top of the ice maker (the one toward the front was a little tricky, since you can't see it at all), then removed the screw that fastens the lower bracket to the side of the frig. Then I lifted up on it slightly to remove it from the two upper screws, then unplugged the wiring harness from the side of the refrigerator and lifted the whole unit out of the frig.

I then removed the plastic cover on the front of the ice maker, pressed on the tab to remove the wiring harness from the old ice maker, and installed it on the new ice maker. I then removed the metal arm from the old ice maker and installed it on the new unit as well. The last part that I moved from the old ice maker to the new one was the lower bracket, as the bracket on the new ice maker was bent during shipping.

Once those parts were swapped, I put the plastic cover on the new ice maker, plugged the wiring harness back into the side of the frig, routed the fill tube into the back on the ice maker assembly, and set the unit back on the two upper screws. I then put the screw back in the lower bracket, tightened the two upper screws, and then put the ice bin back in and turned the water back on. After a couple of hours, I threw out the first couple of batches of ice and it is now working as it had in the past.

I also noticed, when looking at the old ice maker, that the black plastic coating was coming off the ice cube tray, so it was a good time to be replacing it anyway. Overall, a very easy job (I was prepared for swearing, parts being slightly off, etc.) and it would have been a shame to have paid someone to do it.

Used socket set to remove screws. Removed the wire harness, then removed lift arm from old ice maker and then put lift arm on the new ice maker. Reinstall wire harness then installed back in freeze with the screws. Video was very helpful. I will do business with Partselect in the future. Shipping was very fast. Thanks Partselect

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Remover rear cover at bottom of refrigerator. The replacement run capacitor was the same as the original one. The replacement Overload Relay Combination was slightly different. It plugged onto the compressor the same, but the connector where the power came in from the wiring harness was different. I had to cut off the original connector from the wiring harness, and then splice in new connectors onto those two wires which I could then attach to the replacement Overload Relay Combination. Fortunately the connectors I needed were fairly common and I had those available. After that it worked. My suspicion is that the Run Capacitor was fine, and it was just the Overload Relay Combination that failed. Replacing the capacitor without replacing the Overload Relay Combination did not fix the problem.

Once I received the seal/gasket I put it in the dryer on low for 10 mins ( as advised) then I turn the freezer down to 0 and placed a towel over the food to keep it cool. Although the original gasket had rubber with holes to hold the gasket in place the replacement didn't so I found that I had to make sure the gasket was firmly in place while I put the screws back in place. It took an hour or so because I put them in one corner at a time and then tighten them down. I'm swf in my 50s and I did it so anyone can. Also I have long finger nails and still able to do the repair although I drop a few things