59650692001 Kenmore Refrigerator - Instructions

First I ordered the ice maker, but not the wiring harness...didn't fix the problem so I ordered a wiring harness, but ordered the wrong one...so I emailed parts select and got a prompt response on how to return the mistake and which part I actually needed. It was a "special order" but got in within days. Wonderful service!

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Shipping was very fast, part easy to install.
The new filter head was redesigned making it easer to remove the filter.
Loosen the two screws and remove bracket.
Push in the tubing retainers and pull out the tubes.
Remove the two screws holding the filter on to the bracket.
Push tubing in to the fittings on the new filter head, pull out the tubing retainers about 1/16 in.
Make sure tubing is pushed all the way to the bottom of the fitting.
Reinstall bracket and filter head.

The good news is that the part (the wheel was available.) I bought two in the event that the other wheel may break in the future. The bad news is that the housing that holds the wheel was riveted together by the wheel axle. It would have been nice to know that before I bought the part and if the housing with the wheel installed was available. The refrigerator was at my summer house a hundred miles away. Anyway, we had to grind the end of the riveted axle to dislodge it from the wheel housing. With the axle dislodged from the housing we were able to install the wheel and then hammer the end of the axle flat to keep in place, like the original rivet installation. It is not perfect but it held and should be fine. I am glad I was able to get the part and will be back in the future, if in need of other parts.

Had to disassemble ice maker to install part. . .

Removed screws on back cover plate in Freezer, disconnected fan assembly, removed fan assembly, removed propeller from fan assembly, and transferred it to new motor, installed new assembly, reconnected electrical connections, screwed on back cover plate - Viola!

As the prior stories mentioned, this was a fairly easy fix to a nagging problem. Heck, we almost bought a new refer over this, cuz the door would keep popping open.

Needed a screwdriver, and a 5/16" nut driver (mounted in elec. drill). Have two people for this one! Emptying the door would help out tons too. ('course, I didn't do that!)

With the door closed, remove the plastic cover on top by removing 1 phyllips screw. Then, using drill mounted 5/16" nut driver, remove 3 hinge screws. Remove hing by lifting up. Now, carefully open and remove the door. Here is where the 2nd person comes in. There are 2-3 1/4" screws (Must use a 1/4' NUT DRIVER, SOCKET OR MAGNETIC BIT HOLDER) on the bottom of the door to remove the broken plastic cam. Also, you must remove the bad cam from the bottom hinge using I believe the 1/4" nut driver.

Finally , one person lift the door while the other kneels on the floor to help giude the door back onto the bottom hing pin. Close the door, ensuring that the top of the doors are even, and secure the 3 top hinge screws. UR done!

Greg

Remove and clean out everything from the freezer and unplug the refrigerator. Take out the wire shelf in the freezer. (The fan motor is behind the back wall of the freezer, SO YOU CAN KEEP THE REFRIGERATOR CLOSED). Pop off the little cover on the center of the plastic shroud. Remove the little screw and carefully remove the plastic shroud. Remove the plastic cover for the optional ice maker on the upper left corner of the back wall. Take out the two screws in the upper corners on the back wall of the freezer and the last two screws holding the fan motor. The fan motor won't drop, remove the back wall and you will see two screws holding the motor mount. Remover those two screws, and pop the bracket out and separate.Take the two rubber motor mounts off the ends of the old motor and install them on the new motor. (Now you will have to cut the wires off the old motor), unplug the little wire harness, strip the ends and crimp on wire connectors to plug them onto your new motor. Its an AC motor so it shouldn't matter which hot goes on which of the two terminals. JUST MAKE SURE THE GROUND IS CORRECT! (After reinstalling the motor, plug in the refrigerator, turn it on before installing the shroud and make sure the fan is blowing outward. If all is correct, turn the refrigerator off, unplug and finish assembling the freezer. I found the new motor seems to run more efficiently than the old one.

change light bulbs

turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert thermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.