59341TCWW General Electric Washer - Instructions

Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)

After reading all the repair info and reviewing the diagram for my wash machine on this website I was ready to tear into my washer. I removed the front panel and lid to access the tub, pulled out the plastic agitator and revealed the broken inner base hub. The base hub was cracked half way around causing the inner tub to drop down and drag on the outer tub, making the washer sound like it was coming through the wall on a spin cycle. I then unbolted the plastic cap and removed it revealing the hub nut. The most valuable piece of advice in the repair info was abouthe hub nut being a laft hand thread (clockwise to loosen)and that it was on really tight and hard to remove. I put a short 8" pipe wrench on it, because of the lack of clearance in the tub, and hit it with the handle of a all steel hammer to break it loose. Unbolted the balancing straps (4) on the plastic top rim cap that holds the tub in place, unsnapped and removed it, then carefully pulled out the tub. I also had to unscrew the the control panel to reveal and remove the 4 screws holding the fill tube brace so I could push it back to remove the tub. I then took the inner tub outside and took it apart, 3 parts. The top plastic rim, the tub, and the broken base hub that are held together with torx screws. Then it was cleanup time, very dirty on the inside, used a garden hose, scrub brush, sponge, and soap. Cleaned up the hub nut threads with a wire brush and then the outer tub withe a sponge and shop vac. When the base hub broke it caused the inner tub and outer tub to rub together making a groove and plastic shards on the bottom of the outer tub that I had to scrape and sand smooth. A shop vac an absolute necessity in getting all the grime and plastic crumbs out of the outer tub so they don't get in and clog the pump. I received the replacement parts in 2 days! Reassembled in reverse order and everything worked great! Not a bad project at all when you know what to expect, thanks to Part Select.com.

Removed knobs, removed cold and hot inlet hoses,removed top cover, removed output hose, wire plugs, and three screws and replaced the valve.

Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!

Placed a small rope under the agitator and pulled up with a sudden jerk . It popped right up and out . I removed the bolt holding the coupling .I then removed old coupling and replaced with new coupling and bolt. I then installed new agitator pushing down until it clicked into place . All done , less than 15 minutes . Thanks to others that gave their feedback so we could learn what to do .

First and foremost, the job would have taken 2 hrs instead of 8 hrs. The problem was that no one on the help instructions said that the Hub Nut had a LEFT HAND thread and suggested to just break the nut off. Well, after chiseling off most of the nut I drilled small holes through the nut and removed the nut pieces. However; I learned that I had damaged the transmission seal and had to buy a new transmission $183. Had I known this the job would have taken much less time and at a cost of about $50.
PS: The washer runs great.

Repair went good, only wish i had bought a new tub seal, washer, an split ring....but i managed to save the original ones an it seems to be working like new again! thanks Partselect!!!!

unscrewed the old coupling, brushed off yucky build up and replaced, ta da back to washing clothes constantly !

Fold back control panel, pull water level knob off, and unlatch pressure switch. reverse procedure to install new switch.

I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.

First I removed the front panel using the screw driver. I removed the old belt which was in the bottom of the washer. I placed the new belt on the motor and adjusted the pullies. I replaced the front panel. The washer spins much better now than it had for the past year.

Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

The trick is to pull the front cover off by using a putty knife .slide it under the cover at both front corners.it will click on each corner.then pull front cover off .lift off the bottom catch hooks.look for the pump on the bottom right side.unplug the wite connector .take 2-5/16 bolts out holding the bracket.then grab a pliers .squeeze the hose clamps and pull the 2 hoses off.assemble new pump.

Unscrew the 2 screws holding the drain hose clip to the machine - use bucket to get an excess water - remove bad drain line - I installed a new drain hose clip as well - make sure you put the clip on at the same position as the previous hose - push house firmly into opening and screw into machine - pretty easy repair - and I'm a novice

took off front control panel, searched the internet for reasons for my problem, replaced the pressure switch, did not fox my problem, replaced the intake valve which fixed the problem.