58717345790 Kenmore Dishwasher - Instructions

Removed the broken part and disconnected the four wires. Installed new part (two hex head fasteners) attached wires - good to go!
Quick delivery on the part allowed for dishwasher to be down for only a few days after the part was ordered.

Isolated the leak and found the nut had split thereby allowing a loose seal and water penetration. Ordered 2 nuts just in case the other goes and the installation was easy. Unplug the unit, remove baseplate, remove screws under the countertop, and slide the unit out a bit. Use needlenode pliers to remove terminal connection and replaced nut. Reverse it for assembly. 3 minutes tops $6 later it is done. Easy money saved by a DIY.

Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.

I followed the instructions in the video. It was really easy and took less than 15mins. Very happy with the part.

There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.

My husband had the water shut off to the dishwasher, he unplugged the electrical connection then disconnected the inlet water pipe with an adjustable wrench. Once that was done he disconnected the water inlet valve from the frame of the dishwasher and installed the new one , he then reconnected the inlet water pipe and the electrical connection , once that was done he opened the water valve feeding the dishwasher and checked for leaks which were none. Took him about 15 minutes to do it . Make sure you have the proper tools and a roll of Teflon tape before you start the job.

After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!

Six screws, two torque drive screws and, four wires.
Then reverse to install. Pull out old seal wash out groove find center mark on new seal and install be sure and fold notch on bottoms. Easy

Unscrewed the screws on the door, opened it. Swapped out the latch. Screwed the door back together - GOOD AS NEW!

I watched the video on the website on how to remove the top rack, and installed the new wheel and bushing. Simplest fix I ever did.

Easy as pie. I tokk the screws out that held the dishwasher to the counter top out. Then removed the screws holding the strike in place, inserted the new one, installed screws and then rescrewed the 2 screws backintothe countertop. Job done. All told 5 minutes.

I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg

turn water off,remove hoses,remove valve,install valve and hoses,turn water on

The repair was relatively easy and I probably saved enough money as to not have to buy another dishwasher. The part alone was $42. A service call and installation would have made it not cost effective to fix.
The control panel is loosened with phillips head screws on the inside of the door. The latch is attached with the "star" shaped screws. I did not own one of these drivers so I had to leave the house to get one. I used pliers to disconncet the clips from their connections as to not pull the wires from the clips.

shut off water supply, unhook water line first so i could pull the washer out first. pull washer out and the valve is on the lower left if your facin the washer. easy to get to and very simple to change out.