58717245990 Kenmore Dishwasher - Instructions

The Inlet valve was leaking. I removed the old valve in less than 30 min.Note: need bright flashlight! It could have been quicker but I had to lie on the floor and squeeze my big hands under the opening (kick panel). Once I got the two small bolts out, I was able to manipulate the valve out from under the dishwasher, then I carefully removed the two lines. I received the part in 5 days and installed it in 45 minutes. It could have been a faster installation, however I was not about to pull out the whole dishwasher. Again, I was able to manipulate the new valve back in & tighten then test everything.(note: need a bright flashlight to see underneath) I immediately ran a load of dishes and Presto! No leaks and runs like a Swiss watch!

The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.

Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.

1 Removed 2 screws to remove door panel so as to access back of dispenser.
2 Unplugged 2 color-coded wires attached to dispenser
3 Removed 6 screws attaching the dispenser.

Reversed these 3 steps to install new unit.

Easy. Don't even think of calling the repairman.

Removed 6 phillips head screws that hold the front panel in place...let the panel hang in place...then remove 2 torex screws that hold the handle to the dishwasher ( # 25 torex screw driver needed ).......then pry the wire connections off the old handle..remembering where they go on the new latch.....and reverse the process for the new handle install..and for the gasket just follow the inst's on the sheet that comes with the kit..very easy...but when you close the dishwasher with the new gasket..it's going to be very hard to close..( well for me it was )for the 1st few times...

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.

Removed two screws,one on each side of the bottom part of the door. The door cover then comes off. Then 6 screws hold on the dispenser. Shut off power and remove two wire connections. Replace dispenser. Replace lower door cover and two screws. Done.

I used both epoxy on the male threads and then pulled out the case and twisted the flat car body flat kind of a nut. Let it sit for 36 hours and now like new.

Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.

turned off electricity, pulled dishwasher out about a foot, turned off water too dishwasher, removed inlet valve and replaced it with new.

Pulled off the old gasket and replaced it the same way with the new one.

Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

Located where the dishwasher was leaking from and by referencing the parts catalog determined that it was the water valve. I ordered the part from Parts select and replaced the part when it arrived. Replacing the part was very easy and I now have a working dishwasher again.

Replacement was simple.