58715369101C Kenmore Dishwasher - Instructions

First disconnect the power. Open the dishwasher door. Unscrew all of the screws except the top two screws. Unscrew the top two screws last and slide the door off. Unscrew the housing for the control board. Disconnect the wires from the control board(take a picture or mental note where the wires are positioned for reinstalling). Unscrew the control board. Put the new board in and go in reverse order until the job is complete. Good luck.

Under sink: Disconnected drain hose to garbage disposal, shutoff water feed, unplugged power.
Under Dishwasher:
Removed water feed connection.
On top of Dishwasher:
Removed screws anchoring it to cabinet.
Pulled dishwasher out and flipped down so it’s resting on the front.
Removed drain hose on drain pump.
Removed 3 torx screws on pump, greased o-ring on new pump and reinstalled doing the reverse of these instructions.
Took 1 hour and now it works great!

Manually took off melted parts and replaced them with the new ones.

Replaced drain pump. It helped some but still hear some squealing. I suspect the main pump might be worn as well. The drain pump did have some "looseness" to it compared to the new part.

Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.

New right away when we heard the sound, the spring broke. Easy to replace, pull dishwasher out from under countertop, usually held in place by two screws into countertop. Remove screws, pull out dishwasher. Close door, springs will now have the most slack in them. One spring located on each side. Remove spring from one side and replace with new spring to ensure proper spring placement. No actual tools needed as spring rests on a bracket attached to door and other end of spring goes through hole in bottom of dishwasher rack. open door to test for tension as there are several holes to choose from. .

Simple repair.

Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.

#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.

First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!

My upper spray arm attaches to the upper dish rack. It comes in four parts: the spray arm, the bracket which attaches it to the rack, the water funnel, and a plastic nut that holds the pieces together. The nut was worn and wouldn't hold so I replaced that piece and it works great. It took less than one minute to fix.

For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!

For both parts replaced, I simply followed the instructions from your on-line videos. These videos are a great help to make sure that you are installing the part the correct way. Saved us several hundred dollars vs. calling a repairman. Thanks

Watched your video repair was easy.