58715263900A Kenmore Dishwasher - Instructions

See posting under O rings. Get schematic Motor & Pump pg. 8 from pub # 5995487674. Steps: 1) run cycle so most water is pumped out of dishwasher 2) remove front cover to reduce weight of door; 3) disconnect electric plug, hot water hose [NOTE: be prepared for some water from hose], and waste tube all usually found under sink area; 4) remove 2 screws at top of front panel; 5) lower leveling feet to allow best clearance; 6) put towels under front feet to protect floor and slide unit out from under counter; 7) place heavy blanket next to unit to protect floor and tip unit over on its side; 8) disconnect electric plug from motor and remove metal spring clip holding motor (2 torx screws) and pull clip off motor; 9)gently rock motor while lifting to remove from unit [NOTE position of motor for reassembly]; 10) put thin coat of silicon on O rings and place on new motor [look at old motor to make sure O rings are in proper slots; 11) line up motor and gently push new motor back into position; 12) reverse disassemble steps above. 13) run dishwasher through fastest cycle to check for leaks.

Thought the problem was a faulty door gasket (there was a gap in the middle of it) so I ordered new(new one had a gap also) replaced it anyway - maybe it was worn out? Still leaked! Had to sit and stare at it and cycle it through. finally realized the spray arm had a hole in the end that was spraying directly into the gap in the door gasket. Hot glued the hole and it stopped so I bought a new spray arm - no leaky!

First I just rolled out the lower rack assembly, and rolled the new one in. Then I moved onto the upper rack. I started by sliding the off the rail cap lock at the end of the rack. The entire cap does not come off, just the bottom slotted piece. This is done by simply edging out the bottom of the cap, toward the front of the dishwasher, until the bottom slides out of the slot, and lifts out of the way. Then the upper rack was released to roll freely out of the support rail. The next step was to pry off the top of the water diverter. Next was to unscrew the wand assembly from the water diverter that is attached to the upper rack assembly. There are no water lines attached to this, it just directs the jetted water from the top of the dishwasher. Then simply pop the mount from the upper rack. And reassemble the way it came off. This was a simple fix to make the dishwasher like new inside again. The racks purchased from Parts Select fit perfectly with no modifications or trouble. This operation took less than ten minutes. Anyone should be able to handle this operation. If you are afraid to disassemble the upper rack, take a few digital pictures to refer to, and delete them later. This is a tip that has been priceless to me in the past on other projects. Thank you Parts Select.

It took less than a minute to remove the old bottom door gasket - it pulls right out. You wouldn't think the part looks the way it does (a 1.5 inch wide plastic strip that runs the length of the door with rubber gaskets on both ends) but have faith. Trust the diagram/picture - it is the correct part and will fix the leak. The new gasket arrived within a couple days of ordering and was simple to install - no tools. It slides into place in less than a minute and is held in by friction. Problem solved and no more leaks. For under $12 (parts and shipping) I had my dishwasher fixed. A service call by itself would have run $75 - just for someone to show up at the house, and then probably another $50 for parts and labor to install. My wife made the comment "Even I could have fixed that". A very simple and easy repair - you can do it!!!

Unplugged dishwasher, pulled it out. Unclamped hose and unscrewed water source to inlet valve, removed wiring harness, unscrewed bracket and reinstalled new valve. Now have a functioning dishwasher.

My friend bought a used dishwasher at a garage sale, the previous owner had thrown away the drain hose because it was "nasty" they said....remember it could have been cleaned. When I went to install it, I removed the old washer, and discovered that the old hose would not fit on the replacement dishwasher. I went to the local repair shop, armed with the model and serial #'s. they searched and searched their books and could not find the hose part number. they said "good luck" when I left...I went home and looked up the model on your web site, ordered the hose, and in 3 days had the dishwasher installed and running in about 30 minutes...thanks for prompt shipping.. I couldn't believe it arrived so soon...Mowerman

Removed bottom plate and heating element brass nuts. Disconnected heating element. Connected new one then replaced brass nuts. Put bottom plate back on. Very easy.

The Spray arm and the support had come off during operation and subsequently melted on the heating element. This was our fault, as a knife had slipped through the lower dish-rack and acted as a ramp to launch the spray arm as it came around. The support was a simple 1/4 turn counter-clockwise until it clicked into place, drop the strainer basket into position around the support, them push the spray arm into place until the catches snap over the retaining ring molded into the support. All told, about 10 minutes, max.

1. Bottom door gasket removed very easy by grabbing left corning and pulling out. Starting with notch on right side, slide the hard plastic side up at a slight angle to catch the slot the gasket will seat in. Slowly moving toward the left, push gasket into seated position. Notch in gasket will make sure it is in correct position. Push gasket all the way in so that it is flush with bottom edge of door. Watch when first sliding gasket in, it has to g at a slight up angle or it will fall into an empty space.
2. Remove Tub gasket by gripping one side and pulling out. Replace in same fashion making sure the angled wedge of gasket is first part that lays flat in slot. Working from one side to the other, make sure the gasket seats completely. Trim excess if necessary.

I will make a few additions to the other instructions, which are great and let me see that the job was doable. To the tools needed, add pipe tape.
1. Shut off water supply.
2. Removed inlet water hose where it connects to the valve assembly. (This was a pain on my machine—too little room for the wrench, you may have a better tool—but I did get it out, slowly.)
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection (Look for your red and blue wires on the connector, my red was to the top of the solenoid, and reattach with the same grounding) from the solenoid. (This step was a great bit of information; It allowed me to see that I could do the following steps with ease, That is, the unit dropped down where you could work on it.)
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical connection to new valve solenoid.
6. Remounted assembly to the frame.
7. Re-attached the inlet water hose to the hose adapter connection on the valve. (I had to take off the L shaped connector at the bottom of the old valve and add it to the new valve. This was an extra step that required two bigger wrenches to hold the old assembly and unscrew the L joint. I just needed the extra leverage to get the old off and the new on. I am referring to the copper connection that connects to you water supply)
(8) The new valve had a slightly different configuration than my old. The rack it sits on was about an inch or so longer. This meant that I had to readjust my copper pipe just a bit to match up when it was reassembled. No big deal, I had lots of pipe length to work with. Actually, moving the valve a bit further back made more room for the wrench to work—very happy about that. In addition, the hose attachment went from a left exit to a back exit. Doesn’t seem to matter.
(9) Turned on the water, washed some dishes. (Took me about an hour, mostly because of the difficulty with the wrenches. Otherwise—piece of cake)

Just swapped out the old with the new and it has been great. My wife is very happy and that make me very happy.

Remove water supply, take off two screws, attach new part reconnect water supply.

The latch on the soap dispenser got worn out over the past few years on the dishwasher. I tried just puting the detergent into it and running it as usual. The detergent was added Immediatley.. missing the proper timing that would normally dispense it properly. As a result the dishes were not coming out clean and lacked the shiny clean quality we were accustomed to . I ordered the right part, got it quickly and put it in..and were back to doing dishes and having them come out the right way...spotless and clean like they should.

I ordered the replacement racks to replace the rusted ones that had been in my original Fridigaire. I had to take the wheels off the old Upper Rack and attach them to the new upper rack, which was quite easy since they just simply came off by hand with a little bit of pressure. I also needed to take off the spray arm & spray arm funnel in order to attach them to the new Upper Rack assembly. I had to unscrew the spray arm funnel then unattach (without tools) the base of the spray arm from the upper rack. Then I could simply reattach the spray arm base by hand and re-screw on the spray arm funnel onto the base that had been attached to the new upper rack. I also had to take off the Shelf from the old rack and attach it to the new one (which was easily done with a little bit of hand pressure to unattach the Shelf from the old rack). All of this was much easier than I expected it to be, and much easier than I'm explaining I'm sure! I was able to do these rack switches without any tools which was great!

No repair, just replaced the lower rack. Your service is awesome. I received my shipment next day. Thank you so much. I will definitely use your service again.