58715109800 Kenmore Dishwasher - Instructions

First disconnect the power. Open the dishwasher door. Unscrew all of the screws except the top two screws. Unscrew the top two screws last and slide the door off. Unscrew the housing for the control board. Disconnect the wires from the control board(take a picture or mental note where the wires are positioned for reinstalling). Unscrew th ... Read more e control board. Put the new board in and go in reverse order until the job is complete. Good luck.

The unit would not pump the gray water out so I immediately assumed it was a bad pump. Ordered the part and had it the next day. After taking things apart I realized it was a clogged discharge hose and the original pump was still good. Since I had the new pump and everything was already disassembled I decided it would be a good insuran ... Read more ce policy to replace the pump anyways. Easy to install. I didn't even have to pull the unit out. Just did it from underneath.

First I removed the six Phillips head screws that hold the control panel on. Next I removed the two Phillips screws holding the door latch in place. Then attached the new latch and reversed the procedure. Best part was the prompt delivery of the new part. My wife had herself convinced she would be without her dishwasher for several da ... Read more ys.

Replaced the entire top rack with spray bar.

Removing two screws on the inside of the door alows the outside panel to slide down and detach. The soap dispenser connects with six screws and two wires. Remove the dispenser through the inside of the door. Replace, reattach and reasseble in 15 minutes.

Removed old spray arm, fitted new spray arm. VEry easy. Sorry I didn't do it months ago

I took the bottom parts out. This can basically be done without tools. You need a phillips to unscrew 3 screws to remove the stem. Then easily replace with the new one. Putting the spiny washing part was kinda weird because I was afraid to break the nubs off again. I took the whole bottom carriage out so I could see better, pushed down ki ... Read more nda hard and twisted the right way (figure out which way needs to be twisted before hand by looking through the bottom of the stem).

First I removed the bottom dish rack to gain access to the spray arm. I proceeded by pulling straight up on the bottom spray arm, it disconnected with gentle force. The replacement part was not identical, so I determined that it would work by inspecting hole patterns and heat shield configuration. Then I gently pushed the new spray arm ... Read more onto the water supply tube making sure that the spray arm snapped into place. Due to extremely fast ground shipping (less than 20hrs from order to my door) the repair was done within 24 hrs! Boy...was my wife pleased!

I closed on a house a few weeks back. You really don't notice issues with appliances until your living there....the walk through doesn't give you the time to really see anything hidden. Anyway - the dishwasher had appeared to be used to wash grease covered parts from a car so I pulled all the racks and filters out and placed the order for ... Read more replacement parts. I saved hundreds in obtaining replacement parts verse buying a new machine - and I didn't have to sit around waiting for a repairman to do the work for me. I've made several purchases from PartSelect, and will probably making more in the near futre - Thanks!

Removed screws and put new bottom gasket in old one just fell out.

took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.

For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it w ... Read more ith silicone caulk, but may have to replace that - looks easy, .

I foloowed the others who repared the same item. I really appreciated their help and input. The only thing I would add is when they said that you only have to remove the bottom 2 screws on the inside of the dishwasher door they are absolutely correct. But don't look on the very bottom of the door like I did. They are on the inside of the ... Read more door, facing inside. The bottom screw on each side. Thanks for all the help.

Popped off the old spray arm ... INTENTIONALLY, and put new one in. Had to lift off small strainer to allow old arm to release! Be sure to turn arm until it clicks into place, return small strainer/clip, and you are in business!
Most trouble I had was getting this old bo
y up off the floor afterward.
Dished so much cleane ... Read more r now!

This was too easy. I pulled out the bottom rack, spread apart the two clips which are at the bottom of the spray arm with my fingers and pulled out the old broken spray arm. The damage was visible. Then I took the new spray arm ( which looked different but still fit nicely) and gently pushed it into place. Done!

replaced with new lower rack, out with the old, in with the new! Shipping was great new part arrived in 2 days! Great service, and will use again for all parts needed in the future, and will tell everyone about this site! Thanks a bunch!