58714114402 Kenmore Dishwasher - Instructions

Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.

Water leak solved...

Pulled out old gasket from bottom of door with needle nosed pliers and then put in new one in.

Removed the bottom panel on the unit (2 screws hold it on) and pulled the dishwasher out about 4"--after turning off electricity to the unit. Removed the broken spring and the old linkage and replaced them with the new parts. Pushed the diswasher back into place, and replaced the bottom panel. Turned on the electricity and the diswasher door is "good as new." This is quite simple to do; just takes patience.

I removed the dishwasher from the cabinet space (two screws) and manually replaced both springs. I replaced one spring first to see if there would be an improvement when the second new spring was installed. There was much better tension once the second new spring was added.That is why changing both springs is recommended. This was very easy.
Changing the gasket was scary because I thought the the whole door would have to be taken apart. You know nothing ever goes back together the same. I feared that I would create an even bigger leak than what I had. Taken the door apart didnt work for me, so I just pulled the old gasket by hand and pressed in the new one. I made sure that it was seated correctly. Voila no leak.
The dishwasher is running as good as new.
I ordered these parts on Friday morning. They were on my door step Monday morning,
I highly recommend ordering from this site.

Fully open dishwasher door to horizontal position, remove lower dishwasher rack and relocate to another temp location, grab old lower door seal from right or left corner and pull completely out of door, lay the old bottom seal aside facing the same direction as once installed (seal has a notched side which faces the right side of door), match direction of the new seal with the old seal (match the notched side of seal to the right side of door), gently push the seal into the door starting on the right side (notched side of seal fits tightly into a receiving area inside the door), and finally push the remaining portion of the seal into door (aligning with the right side already properly seated inside dishwasher door). Close dishwasher and run water cycle to confirm leak.

Pulled the dishwasher out and laid it on its back. From under the dishwasher I unscrewed three screws and freed the drain pump from some sort of frame. Then with the pliers loosed the orange clamp that held the black hose to it. Then unscrewed the clamp that held the white hose to it. Then pulled out the purple and white fuse wires. These wires were very tight I used pliers to get them off. The pump was free. Be sure to have a bowl to catch all the water. There wasn't a lot but it stinks. Then put it all together the way I took it apart. The dishwasher works perfectly now.

All I had to do was take out old racks and replace with new ones. However the top rack did require taking off the part where the water runs through, it was easy though.

I would like to comment on how quickly and efficiently the parts arrived. I placed my order on a monday morning and am pleased to report by tuesday afternoon they arrived, much to my delight.

I had to remove the dishwasher from under the counter. I then had to unscrew (from the bottom) the bolts that held the heater in place. After that I ran into a problem of disconnecting the wires that ran to the heater. I did not want to "force" the wires off and I was unsure how exactly to remove them. I figured out that they are really hard to pull off but there are no clips holding them on, so you won't break anything off. Once I got the wires off, I was able to screw the nuts onto the new heater and put it back into place.

Place spray arm into receptacle. Take nut and screw on being careful not to over tighten. This will strip the spray arm and the same problem will occur. Easy fix!

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings (~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.

Pulled out old gasket and shield guards and put in new ones. No tools needed. Piece of cake??

Remove 3 screws from stem assembly. Swapped the old for the new, replace screws. Installed and lock lower wash wand. Fixed in 5 min. Great service and prices. My wife thanks you. (Had to hand wash dishes for a few days) thanks

Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!

Our dishwasher sat in a warehouse for a year after our move from CA to TX. When I finally installed it, there was some sort of white mineral deposit that had built up on the heater element. I didn't notice it back in CA. I tried to get as much as possible off but it kept building. So I purchased a new heater element. It's been in for a few weeks and my wife thinks the build up is happening again.
To Repair;
Unscrew the dishwasher from the counter. They'll be one or two screws attaching the dishwasher on the underside of the counter.
Pull the washer out carefully.
Remove any dishes and the bottom rack.
Tilt washer on it's side.
Remove wire connections to heater element (They slide right off but make sure to remember which one goes where)
Unscrew the nuts that are holding the element on. I used some pliers. It wasn't difficult.
Remove old element and replace with new.
Reverse order.