57751H2WW General Electric Washer - Instructions

The worst part of the repair was removing the old hub nut. Don't bother messing with the spanner wrench, unless the washing machine has never been used. Split the nut off with a SHARP cold chisel and a heavy hammer. Be very careful not to damage the threads, because not even GE can or will tell you the die size to re-dress the threads if you damage them. Check drain pump motor to remove debris before using washer. Parts were delivered in a quick and efficient manner.

I watched the video provided by your site and followed it. I removed the clothes softener part from the agitator, Got a good grip on the agitator and pulled up. It came right off. Aligned the new agitator groves and slid it into place, put the fabric softener part back on! Super easy.

Took off the front panel of the washer which exposed electrical wires going to top lid sensor. Took out old sensor installed new. Cut wires from old sensor and spliced wires from new sensor to machines wires that went to old sensor. Replaced front of washer. Washer works fine now.

Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.

Put the drain hose clip on (it will take squeezing but the hose will pass through). There will be a groove that whose width spacing is similar to the clip. Once that's on, insert hose and screw in the clip.

Opened lid and place on agitator ... finished

First I removed the screws that held the drain hose clip to the washer. Then I pulled the hose, along with the clip, completely out of the washer. I then took the old hose out of the washer clip and put the new hose in the new clip; I pushed the hose into the washing maching and tightened the hose clip to the maching with the existing screws. Seriously easy, took less than 15 minutes. And I have virtually no handyman skills at all!

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

Turned off the water and disconnected the water lines. Took of the control panal, only 4 screws and got access to the dual inlet water valve. Device removes with 2 screws and power connectors slide off. Reverse removal and your in business. So easy to do, part was an exact fit. Don't buy a new washer, fix your old one!

replaced them & working fine now....

First I removed the two clamps that hold the inlet drain hose onto the pump. **There may still be water in the hose** This was pretty easy, but a set of vice grips would have been nice. The space is not too cramped, but required a little bit of wiggling. Putting it on was a little bit harder, just because I did not want to tear the hose on the tub or pump inlet. Make sure both are fully seated or else it could still leak. The drain hose and the clip are pretty self explanatory. I tried to buy a generic drain hose at a big box lumber yard, but I could never make it fit right.

Hope this helps.

First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.