56411D0WW General Electric Washer - Instructions

First I removed the front panel by prying it forward with a Screw driver away from the side panels at the top (wrap a shop rag around the Screw driver to keep from scratching the paint). Once you have the panel pried loose at the top ... lean it forward until you can lift it off the tab type hooks at the bottom.
I next unplugged the wires from the motor. The orginal motor had three wires ... two on top and one on the left side. The one on the side is a ground wire for the open frame motor. The replacement motor is sealed and does not require this wire. Just leave it unplugged when the new one is installed.
Next I removed the inlet hose that attaches to the back of the pump. Remove it by loosening the hose clamp and removing it from the bottom of the tub, leaving it attached to the back of the pump. It is much easier to remove and transfer to the new pump once it is out rather than fight with the spring type clamp on the back of the pump in the close quarters inside the machine.
Next I removed the outlet hose from the top of the pump. Squeeze the spring clamp with Pliers and work it up and off the pump.
Now I just used a Socket to remove the two bolts holding the bracket to the inside front of the machine and removed the assembly.
I now removed the inlet hose from the back of the old pump. Just squeeze the spring clamp with Pliers and work it up the hose and off the pump. Transfer the hose to the back of the new pump reusing the same clamp.
I now bolted the assembly back into the machine, reattached the outlet hose to the pump, and then reattached inlet hose to the bottom of the tub. All that was left to do was plug in the two wires to the top front of the pump motor (as I mentioned earlier, leave the side wire from the old pump unplugged as it is not needed on the new one). I then ran the machine for a few moments with the front off to check for any leaks and then put the front panel back on.
The whole replacement cost about $50 and took barely 15 min. from start to finish. The machine now works perfectly.

I replaced the work tub dampening strap because that what everyone recommended to replace for this problem. However the purpose of these straps is to dampen the agitation cycle and they have nothing to with the spin cycle at all. the balance ring assembly had been rubbing on the outer tub so I decided to replace it because of a "balance issue". However the ring is liquid with baffles to counter balance the load as it spins and it still had the liquid inside of it so it was actual not needed. What fixed my issue was I found a bolt laying at the bottom of the washer. This bolt was one of the 4 bolts that hold the outer tub to the metal support. When it feel out the tub was only held in at 3 points not the needed 4. This allowed it to rock a bit in the high speed spin and you thought it was going to fly into a 1000 pieces. I replaced the bolt and other parts since I had paid for them and everything works great now.

I think finding the tools to do the repair took longer than the actual repair!

After unplugging the machine, turning off the water and disconnecting the hoses~ All I had to do was remove the top front panel~ I think that was 3 screws; remove the old part~ 2 screws, disconnecting a hose, and unplugging the 2 connections; put in the new part~ reconnecting the hose, 2 screws, plugging in the two connections; put the front panel back on~ 3 screws; reconnect the hoses, turn the water back on, plug the machine back in then tested it and it worked perfectly!

When the kids got home from school and I told them I fixed it they high fived me and said, "Way to go Mom!"

Removed the front cover of the washer by sliding a screw driver to release the clips. Loosened the 4 nuts that held the drivebelt motor pushed the motor back to release the drive belt. Replaced the drive belt, pulled motor until drive belt was snug and tighted the 4 bolts. At the same time, I replaced the 4 tub dampening straps located at the top of the tub and now the unit is just like new.

Took 4 screws off of face plate, exposed valve, unplugged power supply, removed wire harnesses to hot cold valves, removed hot and cold water hoses from back of washing machine, removed two screws holding valve body to washer,put new valve in and reversed procedure. ta da!!!!!!!!!!

1. Noticed there was and obstruction in the air line that feeds the water level pressure switch. Cleaned out the air line but still had intermittent problem with flooding.
2. Evaluated the fill solenoid valve with meter and was functioning properly
2. Evaluated pressure level switch with meter and noticed that the switch was not changing state as it should when the water level is increasing. Replaced the level pressure switch, but still had problem.
4. Noticed the air line was damaged and had a hole that prevented pressure from building up. Replaced the air line and all is good!

Repaired Agitator - required to pull from the bottom pulling on one side a little more then the other. Once you got loose it comes right off. Under neith there is a bolt that holds on agitator coupler. remove the bolt with wrench or socket wrench and then the agaitator coupler. Replace with new agitator coupler ,make sure grooves are aligned when putting on the rotor. Tap the top of the agitator coupler lightly until it is completely seated. Put the bolt on with wrench or socket wrench. Put the agitator back on over the agitator coupler and agin make sure grooves are alighned and push down until it feels it is seated. When done, give it a light pull to make sure it is secure and then you are done.

drilled off top plate of agitator to gain access ot bolt, removed bolt, removed agitator, replaced coupler and new bolt, snapped in place new agitator.

removed hoses and clamps. removed 2 bolts on pump. put it back together. done 15 min.

followed the instruction on the wiring sheet and removal and repair sheet that comes with the wahing machine. They wee very good directions and the only problem that I had wa getting the 1 and 11/16 inch not off the shaft that holds the tub to the transmission, The main problem was that the transmission had leaked all over the break and the tub would spin while hitting the pipe wrench with a claw hammer. Ended up using a 10 lb sledge hammer to hit the pipe wrench and that finally loosened up the nut, but that was the only real problem i had. I say this was easy except for getting off that nut

I attached the Drain Hose Clip to the Drain Hose Extension and then pushed the drain hose all the way into the drain hole in the back of the machine. I then screwed the clip to the machine. Done. Very painless. Fast delivery... ordered it on Monday, arrived on Tuesday.

Instead of calling a repair man, we decided to look up the problem on the internet. We found that other people had the same problem on a website such as this. We narrowed it down to 2 parts. I opened up the panel on the washer where all the controls are (only 4 screws). Inside the panel was a diagram of the washer. We thought it would most likey be the Water level Pressure Switch. I found the part right away and removed it, I removed two connectors. It was really easy.
We ordered the part online and it came really quick (within two days). I installed the new part(Water level pressure switch) and tested it. The washer worked perfect and did not overflow. We tested it again with a load of laundry. Everything was good.
We saved a lot of time and money by fixing it ourselves. We did not have to wait around all day for a repair man and the part was under $30.00. I am happy the way it all turned out.

First removed front washer access panel.
Next: removed top panel torx screws and disconnected lid switch wiring connector
Next: removed washer top/lid
Next: removed inoperative lid switch (two phillips head screws)
Next: installed new lid switch and screws
Next: installed washer top and connected lid switch wire connector
Next: installed control panel and screws
Next: tested installation
Next: installed front washer access panel
Easy repair. FYI, Parts Select had best price and part arrived within two days of ordering! Highly recommend them for your parts.

Thanks to comments already summited to Partselect I was prepareed for the worst. Once I figured out that you remove the agitator assembly with a swift jerk I was able to access the lower portion of the tub. As others have found out the aluminum nut holding the inner tub can not be removed without a hammer and chisel. Once you get past that things go well. What is left is cleaning the components and re-assembling.

Unplug the appliance first! I removed the front panel and then the top panel with the lid by removing the two screws in the front and pulling up and out and unplugging the electrical connector. I then removed the 4 star screws from the top of the control section. The pressure switch is removed by pressing down on the tab and rotating it. I installed the new pressure switch and connected the three wires one at a time. I then re-routed the new hose and connected both ends. I reassembled everything and tested the new sensor by allowing the machine to fill with water. It now works properly.