56231B0WW General Electric Washer - Instructions

Removed the front panel and lid.
Removed the ring on top of tub and holder.
Had to use a rope and pry board to get the agitator off the shaft. Removed the 7/16 cap screw and removed the plastic agitator block.
Couldn't get the hub nut off and had to use a chisel to break it off (corroded and a left hand thread).
Had to use chisel to free the hub from the center pieces so I could lift out the tub. Then I had to hammer and twist the center piece of the hub to get it off form the transmission shaft.
replace in reverse order without any problem once I realize I had a left hand hub nut.

You tube is the only way to go!

R&R Leaking/Damaged Hose and replaced it with the new one. One thing to be aware of is that after removing screws from the discharge hose upon removing the damaged one there was some water that did not expel from the unit so there was about a cup of water that came out. After removing the leaking hose you will need to remove the retaining plastic piece so that it can be placed on the replacement hose. Or if you ordered one put it on the hose so that it can retain the end of the hose in the washer. The anti-siphon clip is located about half way up the back of the washer it simply clips in place.

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

Pretty much the entire machine has to come apart to replace a transmission. The thing to know that no one mentioned is that the hub nut is reverse threaded - that means righty loosey.
Even if I had known, I tried it both ways and I doubt I could have gotten it off without the chisel as the others also had to do. Split ring was also frozen in place by hard water and soap scum so had to break that cheesey piece of aluminum off also. If you are taking apart your washer, I advise ordering these 2 parts so you will have them after you destroy the old ones trying to get to the part you need to fix.

Thanks to parts select for the exploded diagram!

Remove agitator. Remove coupling. Reinstall new coupling. Reinstall agitator. My only problem was the 7 day delay in getting the part. I expected 2-day delivery.

Pulled agitator off existing agitator coupling. Removed and replaced agitator coupling. Snapped agitator on. One of the easiest appliance repairs I have ever attempted.

I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.

It was really easy. I removed the broken part of the knob from the metal center knob assembly. Cleaned out the "teeth" of the inner knob assembly to remove any debris from the plastic part that broke. I made sure that the metal center knob assembly was pulled out all the way (using the pliers). I inserted the new knob making sure that the knob lined up with the arrow on the dial. Then turned it slightly to ensure that the "teeth" fit together properly. While holding the handle in place, I used the pliers to slide the clip into the slot to keep the knob in place. Once it clicked into place... I was DONE!

Unplug machine, verified the hot water line to the washer was clear. Used screwdriver to remove top panel from washer. Removed faulty (rusted) temperature switch from seating. Then removed each of the wires from the old switch with needlenose pliers and placed them on the proper area of the new switch. Placed the switch back on the panel and screwed the cover back on. Then plugged the unit back in an tested the hot, cold and warm settings. Easy fix.

I had help taking off the old parts,coupling was not easy. But I installed the new parts by my self and I'm 74 years had trouble getting the Agitator Coupling back on, But the straps were easy, Any way I'm back to washing again thanks a bunch

We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.

Just took the dail off and put the knob on and slid the clip on. It was harder to take the glue off that we put on the knob!!

Removed the back of the machine and then flipped the machine on the side and loosened the motor to get the old belt off. A piece came out so we had to check the schematics online to figure out where it went. We believe it was the out-of-balance cut off switch. So to fix that we unplugged the motor assembly and took it out. I also had to fish the spring out of the vacuum, no small task. The worst part was that the belt was so deteriorated that it was super greasy and the carpet ended up a mess. We replaced the motor and belt and now it actually gets the water out of the clothes. Simply Green cleaner was used for the rug and after some strong elbow grease it was cleaned. If not for the mess and the other part and the vacuum snafu, I would have labeled this as easy.

I removed agitator by pulling it up until it unsnaped.

I removed the old agitator coupling by removing the bolt and pulling up while twisting it.

The new coupling looks different than the old part but fits the same.

I pressed the new coupler on to the agitator shaft, reinstalled bolt and pressed agitator on the agitator coupler until it snaped into place.

Washer runs like new!